New Electrical Equipment & Systems Products

Interlock Switch/Control Unit suits Category 3 applications.

Series CM magnetically-coded, non-contact safety interlock switch and control unit features NEMA 6 encapsulated design and is tamper-resistant. Model CM-S4 control provides external device monitoring and has automatic reset button, which allows it to replace safety relay in most applications. Unit will monitor up to 4 switches to Category 3 in accordance with EN954-1. Switch and actuator come in...

Ethernet Switches are suited for dc environments.

DIN rail, wall, and piggyback mount 10/100Base-T Ethernet switches accept voltages from 10-30 Vdc, with surge protection to 3,000 Vdc. ADAM 6521 lets users interconnect 4 copper (RJ-45) and 1 fiber-optic (SC) networks, while ADAM 6520 provides 5 RJ-45 Ethernet ports. Both modules automatically sense 10 or 100 Mbps speeds and provide full and half-duplex flow control. Surge protected to 3,000 Vdc,...

Air Outlets blend with virtually any decor.

Architectural Outlets offer optional replacement for standard white plastic air outlets, and can be located on walls, floor, or ceilings. All round metal outlets are 5 in. dia and come in white, gray, black cast aluminum, or cast brass. Natural wood outlets are available in surface mount or flush mount configurations, with and without louvers, and in choice of oak or maple. Victorian outlet...

Dimming Ballast offers ballast factor of 1.18.

Packaged in low-profile housing, Mark 7 0-10 V Electronic Dimming Ballast is rated at 277 V, allowing operation of four 32 W T8 fluorescent lamps. With dimming ability down to 3% relative light output, ballast will operate between 149 and 27 W. Unit includes programmed-start lamp ignition, total harmonic distortion below 10%, automatic restrike, and operation above 42 kHz. It is suited for big...

PCB Fabrication Notes Guide

The overall purpose of your fabrication notes is to enhance Design for Manufacturability for optimal PCB fabrication and assembly while maintaining applicable industry standards and regulations.

Ethernet Switches include unmanaged switch functions.

Standard-Function, Industrial Ethernet Switches combine switched Ethernet connectivity for 8 or 16 ports with range of 1 or 2 multi-mode, 100 Mbps, glass-fiber port options. Unmanaged switch functions include redundant power supplies, alarm contact, auto negotiation, and cable auto crossing.

Electronic Ballast saves energy.

QUICKTRONICÃ-® High Efficiency Series uses up to 6% less energy than conventional electronic ballasts, without compromising light output or lamp life. It operates 17, 25, 28, 30, and 32 W T8 fluorescent lamps and features less than 10% THD and Universal Voltage. System operates from 120-277 V. Parallel lamp operation provides independent lamp operation, with same wiring and footprint as...

Solderless Connectors facilitate field installation.

Suited for LMR-240 low-loss coaxial cable, EZ-240-SM straight and EZ-240-SM-RA right angle SMA plugs attach to cable without soldering. Center contact attaches to center conductor of cable via beryllium-copper spring fingers, and outer contact crimps onto outer braid of cable. Each connector comes with dual-wall, adhesive-lined shrink boot for strain relief and weather protection.

Solderless Connectors provide snap-on interface.

Suited for LMR-240 low-loss coaxial cable, QMA EZ non-solder connectors provide snap-on version of SMA interface. They are available in straight and right angle versions, designated EZ-240-QMAM (3190-1533) and EZ-240-QM-RA (3190-1539), respectively. LMRÃ-® cables are flexible, non-kinking, low-loss RF transmission line cables that are suitable for use as antenna feeders, system jumpers, and...

Plug-In Relays are rated for 13 A and 1 hp.

Available with clear cover or clear flange-mount cover, general-purpose AZKUP Relays serve as drop-in replacements for other relays in industrial equipment. They feature armature stop that maintains adjustment, Class F insulation system, ac coils from 12-240 V, and dc coils from 12-110 V. UL-recognized products include resistive, general use, and horsepower ac ratings at currents to 13 A and...

Pushbuttons feature solid cast-brass construction.

Weatherproof pushbuttons are offered in 2 versions: TA1786CB, with threaded back plate for Ã-½ in. conduit mounting, and TA1786B, designed for mounting without conduit. Pushbuttons control bells, buzzers, and other low-voltage audible signals. Standard mounting holes are suitable for replacing similar devices. Areas of use include receiving departments, limited-access retail stores, and homes.

Precision Machined Parts for High Tech Applications

For precision and value that sets the standard for quality and craftsmanship, EGS Production Machining is the source for precision and value. Our extensive capabilities and dedication to customer service allow us to deliver the optimal manufacturing solution. See our video to learn more.