New Test & Measurement Products

Test and Development System provides PICMG 3.0 functionality.

Optimized for development of AdvancedTCA main boards and rear transition modules, 14-slot T-Frame for AdvancedTCA(TM) features open-frame design for access to front and rear boards. Offering capacity of 150 W/slot, cooling is bottom pressurized using 3 front-removable fan trays. System includes dual shelf management controllers to monitor, control, and assure proper operation of boards and shelf....

Trace Methane Analyzer is portable and calibration-free.

Model MTO-1000-CH4, based on Cavity Ring-Down Spectroscopy, detects trace amounts of methane down to 2 ppb in milliseconds. Unit offers plug-and-play operation and can measure up to 4 sample gases. Applications include semiconductor fabrication and tools, specialty gas production, UHP gas production, component and system testing, and auto emissions testing.

Triaxial Accelerometer resists mounting strain.

Series 8762A is available in 5, 10, and 50 g ranges with sensitivities from 100-1000 mV/g. Annular shear sensor element has high immunity to base strain and transverse acceleration. Hard-anodized aluminum, 20 mm, cube-shaped housing is ground isolated. Accelerometer uses industry standard Ã-¼-28, 4-pin connector and has three 10-32 tapped holes for secure, stud mounting, assuring reliable...

Inspection System detects small web defects in real-time.

FLAW SCAN SYSTEM detects 0.3mmÃ-² defects on 2 m wide webs, running at 200 m/min. It contains embedded hardware and software with i2S technology for real-time defect detection on continuous web products. Features include real-time display and roll-map, statistical analysis of defect content, and power defect classification tool. Programmable alarm settings are offered for each defect class....

Expanding Access: How to Get At-Home Medical Tests to Market and Patients

This e-book discusses how to get at-home medical tests to market and patients.

RF Counter/Detectors display frequency and signal strength.

Hand-held Models 103, 104, 105, and 106 utilize RF and microprocessor circuitry to detect audio/video wireless transmissions. Frequency detection ranges are 1 MHz to 3 GHz, 10 Hz to 3 GHz, 1 MHz to 3 GHz, and 30 MHz to 2.8 GHz, respectively. Users can simultaneously view signal strength on 16-section bargraph and detected frequency on LCD screen. All units include 4 selectable gate speeds,...

Flow Meters are offered in 5 port sizes from -½ to 2 in.

EZ-ViewÃ-® Flow Meters are constructed of Polysulfone plastic and can be installed in any position. Direct reading meters are accurate to Ã-

Particulate Analyzers are suited for in-use measurements.

SEMTECH QCM (quartz crystal microbalance) and MPS (micro-proportional sampler) provide transient, mass measurement of particulate matter (PM) in engine exhausts. Former calculates mass of PM with resolution approaching 1 nanogram. SEMTECH MPS delivers response times of 0.1 sec and operational speeds of greater than 5 Hz. Based on LabviewÃ-® platform, both are configurable for short, high-mass...

Digital Force Indicator suited for textile testing.

Digital pi Tenacity Meter measures breaking strength and tenacity of fibers, yarns, and fabrics. It provides indication of live load, plus display of breaking strength and tenacity after test has been completed. Results remain displayed until cleared by operator or when next test commences. Programmable calibration is password protected and stored in permanent nonvolatile memory. Unit includes...

Infrared Thermometer measures up to 500-

Mini Infrared Thermometer, Model 42500 measures surface temperature from -4 to 500Ã-

Chart Recorders employ removable pen arm.

Temptrace 4 in. Temperature and 4 in. Pressure Chart Recorders are offered with pen arm that lifts completely off chart, allowing for pen and chart replacement. After replacement, device snaps back into place for clear and accurate chart recording. Recorders include on/off switch, external battery access, and keyhole back for wall mounting. Pressure Chart Recorder features NEMA 4x water resistant...

Precision Machining Solutions with Over 25 Years of Experience

Quality, customer service, and unbeatable value are the hallmarks of Hogge Precision. Since 1989 we have built a reputation as the go-to precision machining source, servicing many demanding industries. For CNC machining and screw machining, there are few manufacturers that can match our capabilities and expertise. See our video to learn more.