New Electrical Equipment & Systems Products

Swing Arm Clamps are offered in 25 and 32 mm bore sizes.

Available in 4 bore sizes from 25-50 mm, Series PB employs hardened helical spline and 3 hardened drive balls. Keyed interface between rod and arm ensures location and facilitates installation, while rear plug allows arm position to be adjusted up to 90Ã-

Wire-to-Board Connector suits high-density applications.

GH disconnectable, crimp style connector series is available in 2-15 circuits rated 1.0 A @ 50 V ac/dc and accommodates wire sizes AWG No. 30-26. Top and side entry, .049 in. pitch, SMT connectors are polarized and have positive locking feature with audible click/tactile feedback. Fork-shaped header contacts are supported by grooves on housing walls designed to prevent deformation. Insulation OD...

DC/DC Buck Regulators optimize low-power applications.

Synchronous PWM current mode DC/DC converter models FAN2011 and FAN2012 provide 95% efficiency, 1.5 A continuous load current, and fixed 1.3 MHz operating frequency in 6-terminal, 3 x 3 mm MLP package. Products feature on-chip MOSFETs and adjustable output voltage from 0.8 V to VIN. Model FAN2011 is always on, while FAN2012 has enable pin that lets designers implement power management schemes for...

Resonant Transformer features Litz wire-free design.

Designed to improve performance of switch-mode power supplies using high performance resonant mode controllers, HXTR18002 employs Litz wire-free design that reduces leakage inductance and promotes heat transfer. Transformer, based on Hyper-X Magnetic Technology(TM), features 22:25 turns ratio and operates from 75-500 kHz, with typical primary effective ACR of less than 0.25 ohm at 500 kHz.

Seal Stuff In, Seal Stuff Out

One of the best ways to make sure that your machinery stays up and running in the face of adversity is to make sure that it's properly sealed. Of course, it's not always easy to determine whether the integrity of your seals are up to par. How can you tell when you have a problem?

Lightning Protector suits Gigabit Ethernet systems.

Available in 12 configurations, Series ALPU protectors use fast-acting silicon avalanche suppression diodes and reduced capacitance protection circuitry that permits high signal bandwidth. Units deliver protection to IEC 61000-4-5 standards, and can protect up to 8 Cat-5e pairs as well as various configurations of dc power for POE applications. Measuring 5.5 x 4 x 3 in., metal or plastic...

Programmable Tilt Switch offers -

Single-Axis Model MCL combines microprocessor-based electronics and MCL TrueTILT(TM) Sensor in high-impact case. It features +4.5-28 V single power supply, as well as unidirectional and bi-directional open collector outputs. Non-mercury, field-settable switch avoids wide hysteresis errors caused by temperature in most mercury and gravity ball switches. It can be configured by factory or user for...

Miniature Terminal Blocks include wire guard feature.

With overall height of 8 mm, Series DGWG84V8 is suited for situations where PCB real estate is critical in initial design criteria. Modular design allows for configurations from 2-24 poles with operating voltage of 300 V at 10 A. Wire Guard openings accept solid or stranded wire range of 18-24 AWG with guard feature configuring to conductor as clamping screw is tightened. PC mounting pins are...

Forward Converter Transformer suits telecom applications.

Based on Hyper-X Magnetic Technology(TM), HXTF00140 is designed for forward converters with 500 kHz switching frequencies. It measures under 0.25 in. high and helps improve performance of switch-mode power supplies. With densities of 682 W/in.Ã-³ and 525 A/in.Ã-³ product delivers 1.3 V @ 40 A with dc inputs from 36-72 V. It exhibits leakage inductance of 0.6 Ã-µH max @ 500 kHz and...

Toggle Switch is protected against accidental actuation.

Professional-grade 12000X778 Series features full rear sealing, locking lever actuator, and double shell case for mechanical strength and electrical insulation. With IP67-sealed front panels, 2-, 3- or 4-pole double throw models are offered in momentary and maintained, 2- and 3-position configurations. Contact mechanism suits applications of 10 mA @ 50 mV and 5 Vdc min with electrical life up to...

ATEX-Certified Enclosures suit hazardous environments.

To address global issue of ATEX certification, Ex-range of enclosures and terminals are designed and certified for use in Zone 0, 1, and 2 environments. Units support whatever internal wire termination method is required, including screw connection, tension-clamp, and insulation displacement. Enclosures can be milled, drilled, painted, and assembled to customer's exact specifications.

SEALTITE® Fittings and Cord Grips Offer Longer Lasting Protection

Anamet Electrical's 316 Stainless steel SEALTITE® fittings and UL-listed cord grips protect sensitive wiring components from fluids, corrosive contaminations, bumps, and abrasions with a steel core and liquid tight conduit jacket. Check out this video to learn more.