Emissions Monitoring System offers 2-point stream switching.
MicroCEM(TM) TS field-mountable, continuous emissions monitoring system allows facilities to monitor 2 sample points/stacks with one analyzer system. Monitor extracts sample gas, conditions sample, analyzes sample for desired components, and processes emissions data by utilizing calibration validation calculations/procedures and oxygen diluent corrections. MicroCEM TS stores relevant raw/diluent...
Read More »Sound Level Monitor helps maintain desired noise levels.
Model SL120 examines decibel levels and alerts users when they exceed pre-set limits. Large LCD display allows unit to be read from distances greater than 30 ft. Alarm system indicates when quiet is needed through use of relay modules, which illuminate large warning signs and remote noise indicators. Featuring programmable high limit set point of 30-130 db, ANSI Type 2 unit is suited for...
Read More »Adapters/Receivers provide mobile connectivity.
CompactFlash Adapter provides Class II Bluetooth connectivity capable of communication within 32 ft radius. With attached external antenna, USB Class I Adapter enables communication within radius of 328 ft, while USB Class II Adapter, with integrated antenna, communicates within 32 ft radius. Available with Bluetooth, USB, or CompactFlash interfaces, GPS Receivers are designed to GPS-enable...
Read More »Endoscope inspects welds on tubes and pipes.
Endoscope is supplied with 1 m flexible shaft fitted with 8 mm diameter probe. To facilitate inspection of internal weld profiles, 90Ã-
Read More »Pressure Sensor Selection Guide
This white paper provides information and a guideline for pressure sensor selection.
Read More »Flow Meter is rated IP 65/NEMA 4.
Smart Flow Meter is available in two capacities, Model SFM 275A for flows from 180-2,100 ftÃ-³/hr, and Model SFM 350 for flows from 350-7,000 ftÃ-³/hr. Meter can be used as feeder, meter, or batcher with accuracy better than +0.5% or +1%, depending on application. With use of built-in bypass feature, it can be tared at any time during measuring process. Product is suited for high rate...
Read More »TOC Analyzer features detection limit of 4 ppb.
Measuring up to 25,000 ppm, Online TOC-Vc Analyzer enables multipoint calibration curve to be created from single high standard. Unit offers choice of data output via analog mode or RS232. Six contact outputs monitor status, errors, and alarms while contact inputs permit remote start, stop, calibration, and alarm reset. Analyzer is compatible with Total Nitrogen Module for simultaneous carbon and...
Read More »Conductivity Controller accepts RTD sensors for ATC.
CON 2000 Ã-½-DIN Controller features 7 measurement ranges from 0-2 Ã-µS/cm to 0-1,000 mS/cm. It offers on/off, proportional, or proportional integral control modes with pulse length or pulse frequency options, and accepts 2- or 4-cell conductivity electrodes with cell constants between K=0.01 and K=10. Programming and calibration data are protected by 2-level passwords and are stored in...
Read More »DVR replaces VCRs in security system applications.
With on-board networking capabilities for integration into networked systems, self-contained Model WJ-HD220 provides 8 channel inputs plus camera control functionality. It offers 120 Gb recording capacity, pre-alarm screening, time lapse recording, as well as playback and monitoring capabilities. Featuring coax control up to 3,000 feet using Panasonic VD2 for dome camera pan/tilt/zoom operations,...
Read More »Portable Gas Analyzer provides flue gas analysis.
Incorporating pipe pressure leak detector, draft and differential pressure meter, and 7 in. flue gas dual probe, Model BTU 2000+ analyzes O2, CO, and calculates CO2. Weighing 2 lb, unit has magnetic rubber shell for hands-free use, and also provides remote PLC communication capabilities. Other features include impact printer, gas sniffer, 250 test memory, and Windows-based software.
Read More »IR Thermometer takes non-contact measurements.
MicroRay Pro, suited for HVAC monitoring and maintenance, has temperature reading capability from -5 to +800Ã-ºF. Portable unit provides laser pinpointing to identify measured surface area. Areas of use include bearings, motors, valves, electrical switches, hot spots, engine performances, floor heating systems, and piping.
Read More »Custom Fabrication & Machining Services with Over 30 Years of Experience
As a trusted manufacturer to customers across a broad range of industries, Key Gas Components is a premier provider of CNC machining and tube fabrication. Our entire organization is quality driven and customer-centric, with broad-based manufacturing capabilities that can accommodate the most challenging requirements. See our video to learn more.
Read More »