New Electrical Equipment & Systems Products

Grips suit pipe pulling and boring pull-backs.

King Grips are compatible with PVC and poly pipes ranging from -¾ to 4 in. They are plated for rust prevention and provide full pipe end cover. Reusable Wire Mesh Grips feature coated galvanized cable, reverse weave, and single wire ball. They can be used for pulling irrigation pipe, insulated wire, wire rope, tubing, PVC, and bare conductors. Grips are easily identifiable by tags positioned...

HVAC Disconnect has compliant ground-fault receptacle.

Model B222-60NFGF is a 60 A, non-fused ac disconnect pullout with built-in, 110 V ground-fault receptacle for residential and light-commercial applications. Receptacle meets requirement of 210.63 and 210.8 of 2002 NECÃ-®. Rotating design and ample space allow for easy wiring.

Stepping Motor can hold torque up to 83 oz-in.

Available in 1.34, 1.57, and 1.89 in. lengths, 1.8Ã-º, NEMA size 17 Super Torque Step Motor is capable of holding torque from 30-83 oz-in., depending on length. Unipolar and bipolar windings are available to allow for torque and speed required to accommodate specific needs. Product is suited for use in applications where load capacities are critical to precision system operation.

DC/DC Controllers provide output voltages down to 0.8 V.

Models MIC2198/9, offering current capability of 20 A, can power CPUs, DSPs, and FPGAs with up to 95% efficiency. Input voltage range is 4.5-32 V, making them suitable for 5, 12, and 24 V power bus systems. Model MIC2198 operates at 500 kHz, while Model MIC2199 operates at 300 kHz. Both units are housed in 4 x 4 mm MLFTM 12-lead package, and provide PWM current mode control, cycle-by-cycle...

UNLOCKING THE HIDDEN POTENTIAL OF MANUFACTURING: How lubricants can help increase productivity and reduce total cost of ownership

This paper illustrates how manufacturing companies have successfully worked with Shell Lubricants to upgrade their lubrication and extract value by reducing TCO and improving equipment productivity.

AC/DC Power Supplies offer current sharing capabilities.

Equipped with power-good LED indicator and output adjustment potentiometer, PSP300 and PSP500 Series active power factor corrected enclosed switching power supplies provide output power over 300 and 500 W ranges, respectively. All models accept Universal Input from 85-265 Vac, and some models provide single outputs from 5-48 Vdc. Features include soft-start circuitry, integral EMI filtering,...

Cable Assemblies are manufactured to customer requirements.

Electrical and microwave telecommunication cable assemblies are custom manufactured using RF connectors and coax/triax cables to meet specific design requirements. Featuring potted and encapsulated connectors, strain-relief boots, and other special related materials, UL/CSA approved assemblies can be built to withstand extreme conditions. For military use, they can be hand soldered and certified...

Turbine Generators provide high power density.

HPD Turbine Generators, for steam and gas applications, offer vacuum-pressure impregnation of all rotor and stator windings, 100% epoxy solids, steel construction, and dynamic balancing of rotor and shaft. Products may be configured to meet unique needs. Available with power ratings from 3.5-8.5 MW and voltages up to 15 kV, generators weigh 36,000 lb (8.5 MW unit).

DC/DC Converters provide isolated output.

Series 5E 25/30 W DC/DC converters feature pi-input filter and 2:1 input voltage ranges of 9-18, 18-36, and 36-72 Vdc. Regulated, low ripple, single, dual, and triple outputs are available. CMOS/TTL-compatible, remote on/off control allows output to be put into powered down, stand-by mode. Single-output converters have external Output Trim that allows output voltage to be set within Ã-

Power Supplies suit bus-networking applications.

FieldLinkÃ-® Power Supplies are available in models designed specifically for AS-interface, Foundation Fieldbus, DeviceNet, Modbus, and Profibus PA and DP. Solid-state circuitry limits current output under overload or short-circuit conditions and restricts power to 100 W. Potential damage to networking components is eliminated. Units are DIN rail mounted and comply with requirements for Class...

Resistor Network offers stability of 0.01% at 0.1 W.

Made up of 4 independent Bulk MetalÃ-® Foil resistors in dual in-line, molded epoxy package, SMN series surface-mount resistor network provides tracking TCR of 1 ppm/Ã-

Neagle Choice, LLC Announces New Available Services

Neagle Choice has long been known as a quality source for commercial sewing, printing, die cutting, and the manufacturing of a wide range of custom products. Enhancing our service capabilities has been the key to our success, and has driven our growth into many new and exciting markets. Continuing on this trajectory, we now offer precision laser cutting and etching, adding to our long line of manufacturing services. See our video to learn all about it.