New Electrical Equipment & Systems Products

Power Relay suits HVAC and major appliances.

Model FTR-K3, a 1 Form A relay with nominal operating power of 780 mW, measures 30.1 x 15.7 x 23.3 mm. Rated for max load of 20 A at 250 Vac, it is suited for switching compressor and inverter loads in air conditioners and refrigerators. Relay features 8 mm clearance distance and 9.5 mm creepage distance between coil and contacts for high insulation resistance. Made from lead-free materials, it...

Switches combine Ethernet technology with MPLS.

Developed from IP/MPLS baseline hardware and software architecture, Model 7450 Ethernet Service Switch delivers Ethernet services with SLAs. Control plane scales to support thousands of simultaneous Ethernet services while maintaining ability to recover from outages in less than 50 ms. Model 1662 Packet Ring Switch uses MPLS-enabled Resilient Packet Ring technology to deliver point-to-point and...

DC Micro Motors suit high-volume applications.

Featuring precise step angle, Stepper Motors range in size from 6-42 mm dia. Vibrator Motors range from 3.6-6 mm diameter, while Brush Motors range from 4-34 mm, and Brushless Motors range from 19-60 mm diameter. With SMD mounting and wide range of connection choices, motors are suited for camera lens movement, robotics, cell phones, gaming, biometric scanning, dispensing equipment, CD-DVD...

DC/DC Converter delivers up to 1.2 A at 95% efficiency.

Synchronous, fixed-frequency, buck-boost Model LTC3443 optimizes battery run-time for single-cell Li-Ion, multi-cell alkaline, or NiMH battery-powered applications. It operates from input voltage of 2.4-5.5V and can provide up to 1.2 A of output current at fixed output voltage between 2.4-5.25V. Operating frequency is set internally to 600 kHz and can be synchronized up to 1.2 MHz. Burst...

Does an IT MSP Really Add Value to a Manufacturing Environment?

To find out more about how IT managed service providers can specifically help your manufacturing company, download now.

Digital-to-Analog Converter comes in 3 x 3 mm package.

Model LTC2601 integrates voltage output 16-Bit DAC in 10-pin DFN package. It allows multiple DACs to be controlled with 3 wires using daisy-chainable SPI serial interface. Operating with voltages from 2.5-5.5 V, unit's DAC output can directly drive capacitive loads to 1,000 pF or current loads to 15 mA. Asynchronous update pin enables DAC update to be synchronized to hardware signal as well as...

Dual 2-Phase Controller regulates low output voltages.

Synchronous dc/dc Model LTC3802, with 3-30 V input range, operates without sense resistors. Current limit is adjustable, and overcurrent is detected by sensing voltage drop across external MOSFET. With nominal 550 kHz switching frequency, phase lockable from 300-750 kHz, controller regulates output voltages as low as 0.6 V. IC employs modulation architecture and features programmable up/down...

Connectors and Tubing keep crankcase lines from freezing.

Heated NORMAQUICK-® V2 quick-connector and NORMAFLEX-® plastic tubing prevent condensation in crankcase ventilation lines from freezing. Tubing can be heated throughout or concentrated in problem areas. Connector is available in various sizes in straight and 90-° configurations, while smooth or corrugated tubing is offered with single- and multi-layer construction.

Analog Switch is suited for portable audio designs.

With dual SPDT configuration, FSA2257 NC switch allows for flexible routing of audio signals in portable devices. Lead-free product comes in 10-terminal, leadless MicroPak(TM) package and provides bi-directional operation, allowing configuration as multiplexer or demultiplexer. Characteristics include 0.95 ohm On resistance, 0.002% total harmonic distortion, 1.65-5.5 V operating voltage range,...

Vibratory Feeders suit light duty dosing.

Vibratory Feeders are suited for batching, weighing, and dosing applications where small volumes are conveyed and micro-fine, accurate control is required for feed rate. All models can be supplied in accordance with FDA and USDA specifications for use in food, drug, and cosmetic industries.

Power Supplies are UL/cUL, CE/TUV, and FCC approved.

DIN rail mountable, Industrial Power Supplies consist of 24 V, switched DC units in 210 mA, 420 mA, 750 mA, 1.25 A, 2.5 A, 5 A, and 10 A sizes. They autoselect voltages and include voltage adjuster pot and DC indication light on front panel. Suited for packaging, food, plastics, and automobile industries, Class 2 power supplies include short circuit protection, internal input filter, and low heat...

Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine

CS Unitec is a leader in power tools designed for industrial applications, with products that set the standard for robust performance and industry-leading reliability. Adding to our long list of innovation is a new line of pipe cutting machines. For cutting and beveling pipe up to 2" in thickness and diameters from 12" to 63", no other cutting system comes close. See our video to learn more.