New Electrical Equipment & Systems Products

Mounting Kits reduce setups times for CNC machining.

Zero Point Mounting Kits contain all required components to create quick pallet change system for CNC machinery. Speedy Module plates, mounted onto machine table or tooling block, clamp onto nipples attached to bottom of existing fixture plates. Attaching nipples to all fixtures lets users change pallets in seconds. Module plates can also be mounted to inspection machines, making it possible to...

Dual Channel DC/DC Converter delivers 1.6 A per channel.

Supplied in 16-lead, 5 x 4 mm DFN package, LT3506 and LT3506A dual current mode PWM step-down DC/DC converters operate from 3.6-25 V input and feature two 2 A power switches. Each channel offers independent shutdown and soft-start pins. While LT3506 switches at 575 kHz, LT3506A switches at 1.1 MHz. Both have soft-start, internal cycle-by-cycle current limit, and low VCESAT (210 mV @ 1 A) internal...

Compressor Pressure Switches provide pump and motor control.

With 20 A electrical rating, Series CX ranges from 25-175 psig and is suitable for regulating tank pressures on small air compressors. Units feature adjustable set point and deadband, and are not mounting sensitive. Offered in 1- and 4-port models, switches come with un-loader valve, which prevents compressors from starting under load. They also include auto/off disconnect lever for manually...

Foundation Fieldbus Cable suits industrial networks.

Intended for plant environments that use networked discrete or process automation and control, DataCell Cable is rated for Instrument Tray Cable/Power Limited Tray Cable exposed-run applications and complies with FOUNDATION fieldbus H1 specification for type A. It is available in 18 AWG with foil or braided shield, and with or without ground wire. PVC jacket is resistant to oil, sunlight, and...

Bulk Briner 101: What You Need to Know When Considering a Bulk Briner

If you're thinking about switching from packaged to bulk salt, check out this white paper and see if a bulk briner is right for your application.

Motor Controller suits 1.8 and sub-1.8 in. hard disk drives.

Integrating all circuits needed to control and drive HDD spindle motor and voice coil actuator, Model L7208 HDD is intended for portable consumer electronics. Smooth DriveÃ-® pseudo-sinusoidal digital-drive technology minimizes acoustic noise from spindle motor. Class AB output stage has zero dead-band and minimal crossover distortion, and power FETs deliver up to 0.5 A peak current....

Cover Kit hides flat screen TV cables.

Flat Screen TV Cord Cover Kit hides cables running from wall-mounted TV to audio/video components located beneath in rack or cabinet in low-profile channel with ample room for all associated cables. Both base and cover can be cut to length and painted to match any surrounding area. Cover snaps on and can be removed if cables need to be added. Each kit contains pre-drilled, 4 ft base and snap-on...

Battery features thin plate, pure lead design.

With deep cycle capability of 400 cycles at 80% DOD and deep discharge recovery of up to 90% recharge in less than an hour, Genesis XE60 is suited for applications requiring high power in short duration. Tolerant against high levels of shock, heat, and vibration, 12 V unit weighs 53 lb and measures 10.85 x 6.99 x 7.82 in. VRLA AGM battery has M6 female no-maintenance terminals, and nominal...

Connector Systems have 2.00 mm pitch and 0.1 mm coplanarity.

With maximum current rating of 2 A per contact, Minitek(TM) 2.00 mm pitch modular connector systems include PCB receptacles, slim-line and shrouded headers, crimp-to-wire housings and terminals, unshrouded headers, and IDC receptacles. They are available in surface-mount and through-hole double-row versions in either straight or right angle orientation from 4-50 positions.

Inverters suit electroluminescent backlit LCDs or devices.

Vacuum encapsulated Smart Force Series DC-AC inverters prolong lamp life by automatically adjusting operating voltage and frequency. Suited for battery-operated devices, LPS series consumes less than 400 mW per unit load, while JLA Series powers imported EL lamps used to backlight LCD modules. Inverters are available in Standard E600, E300, EMini-EL for small displays in portable, hand-held...

Feed-Through Receptacles have explosionproof design.

Offering safe way to implement explosionproof protection in Class I, Division 2 areas, 7/8-16UN minifastÃ-® receptacles are available in 2- to 6-wire types with 316 stainless steel housing and keyed connector. Incorporated minifastÃ-® quick-disconnect eliminates field terminations and is compatible with FM-approved cordsets. Fully potted with force-resistant compound tested to 9,000 psi,...

Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine

CS Unitec is a leader in power tools designed for industrial applications, with products that set the standard for robust performance and industry-leading reliability. Adding to our long list of innovation is a new line of pipe cutting machines. For cutting and beveling pipe up to 2" in thickness and diameters from 12" to 63", no other cutting system comes close. See our video to learn more.