New Mechanical Power Transmission Products

Solids Reduction Unit retrofits to twin shaft grinders.

Annihilator twin shaft solids reduction unit is supplied with seals and bearings housed in replaceable stainless steel cartridge, which allows on-site replacement. Counter-rotating, hexagonal shaft design coupled with hardened steel cutters provide maximum shredding strength necessary to process 300 to 4,250 GPM of influent. Annihilator is fitted with toothed cutting spacers, electronic control...

Failsafe Brake fits stepper and servo motors.

Model RFEB power-off brake mounts on front end of standard NEMA 23 and NEMA 34 stepper or servo motors to prevent machine from operating or for holding load in place when power fails. It has spring-set design, ball bearing supported output shaft, and operates at speeds to 8,000 rpm. Brake is available in 24 and 90 Vdc versions. Applications include factory automation, material handling, robotics,...

Spring Set Brakes hold loads when power fails.

ERD Series electrically-released, spring set brakes perform dynamic stopping and fail-safe, power-off braking to hold loads in event of electrical outage. Brakes are available in 8 sizes, from 3.3 to 9.9 in. dia with torque capacities from 4 to 220 lb ft. Brakes permit stopping and holding in both directions, and can stop loads from motor speeds up to 3600 rpm. Applications include hoists,...

Hydraulic Power Unit drives bar shears.

VHPI-3 Hydraulic Power Unit, suitable for use with lightweight Bar Shears, weighs 30 lbs, and can be carried from one location to another. Fluid flow ranges from 1 GPM at low pressure to reduced flow at higher pressure. Its 1/2 HP motor draws 10 amps at 110 Volts.

Bearing Solutions For Your Robotics and Automation Applications

This ebook provides an in-depth overview into bearing solutions for your robotics and automation applications.

UV-resistant Wrap provides abrasion protection.

Heli-TubeÃ-® UV-Resistant Spirally Cut Polyethylene Wrap bundles and protects hoses against abrasion in outdoor environments where flexibility is required, and permits breakouts and anchoring. Featuring 1 1/2 in. OD size that can bundle hoses up to 10 in. dia, wrap is UL recognized and comes in 10 sizes ranging from 1/8 to l 1/2 in. It is unaffected by direct sunlight, fuels, oils,...

Linear Drive Actuators eliminate friction and backlash.

Series BB 2-piece systems consist of passive, magnet-free, stationary platen, serving as precision linear guideway and moving forcer with built-in roller bearings. All bearings are magnetically preloaded and do not require gap adjustments. Units have force ranges from 5 to 15 lb, open loop motion repeatability of 0.0001 in., and travel length up to 80 in. Forcers are capable of velocities of 60...

Protective Sleeves save labor.

Coated, ballistic Cordura(R) Sidewinder sleeves, with industrial hook and loop closure, allow easy assembly and removal. Sleeves install without disconnecting hydraulic, electrical, and pneumatic hose and cable bundling and can be removed easily for hose maintenance. Material is available in variety of circumferences and bulk lengths to 150 ft for OEM and maintenance operations.

Gearing works with standard screw.

Precision gearing works with threaded long length rods and adapts to rotary or linear motion machinery. It is capable of fine adjustment and positive positioning. Gear is available in variety of standard sizes or can be made to order.

Feedthrough Actuator provides motion control in vacuum.

Chamberlink, single-unit combination feedthrough and servo actuator, allows output shaft to operate in vacuum without shaft seals, preventing leaks. It is available in sizes 10, 14, and 32, with output torques from 10 to 300 in.-lb and output speeds of 10 to 50 rpm. Actuator is rated for vacuum levels of 10E-8 Torr.

Pneumatic Actuator works like human muscle.

Type MAS Fluidic Muscle uses material deformation and flexure to achieve linear motion. Basic concept involves wrapping flexible hose with non-elastic fibers arranged in rhomboidal fashion. This results in 3D grid pattern. When compressed air is introduced into system, grid pattern is deformed, pulling force is generated in axial direction, and muscle shortens. Range includes 10, 20 and 40 mm...

The Carbontec System: A Smarter Way to Heat Your Buildings

Carbontec's paper-thin radiant heating systems reduce energy consumption costs by warming the building surfaces instead of controlling air temperature. Check out our video to learn more.