New Mechanical Power Transmission Products

Linear Actuators suit rapid motion applications.

Size 17 hybrid linear actuators are available with 0.9Ã-

Worm Gear Drives provide ratios from 1:1 to 60:1.

DAW Series multi-speed transmissions will shift on-the-fly under full load. Model DAW is rated at up to 50 input HP at 1800 RPM and comes in 4 basic configurations. DAW-S is single input with single output shaft; DAW-SD is single input with dual output shafts that may be solid or split; DAW-DS is single input with dual output shafts and output shafts are coaxial shaft-over-shaft; DAW-SI is single...

Servo Motors feature internal Hall sensor feedback.

ELCOM ST(TM) slotted brushless DC servo motors, with 6-slot lamination design, are available in stack lengths of 1/2, 1, 1 1/2, and 2 in. All have 4-pole rotor featuring neodymium iron-bore magnets. Continuous torque output up to 49 oz-in. can be achieved with motor speeds up to 8,000 RPM and power output up to 188 watts. Mounting configuration is consistent with NEMA 23 standards.

Flexible Discs grind and blend in one step.

Cotton fiber layers in Cut-N-Finish discs are impregnated with aluminum oxide grains and then pressed and bonded together, so discs constantly reveal fresh abrasives as they work. Suitable for edge grinding, surface blending, and working fillet welds on stainless steel and aluminum, discs are available in 4 1/2 and 7 in. sizes, and in A24, A36, A54, and A80 grit sizes in both flexible and medium...

Bearing Solutions For Recreational Applications

This white paper provides and overview of bearing solutions for recreational applications.

Mini Flap Discs work with small air grinders.

POLIFAN(R) flap discs are available in sizes of 2 and 3 in. dia., in flat and conical styles, and in zirconia grain with grit range 24 through 120. Discs are able to grind and finish in one step, and stay aggressive throughout life of disc. Flap discs do not require backing, run cooler, and are suitable for use on all materials.

Direct Drive Motor comes in two parts.

Brushless ULT frameless motor has separate rotor and stator that can be integrated into precision mechanical assemblies. Low profile motor has axial lengths as small as 10 mm, diameters up to 165 mm, and through holes up to 120 mm, making it suitable for direct drive rotary applications. Models are available with 30 to 600 oz-in of torque output. Its three phase motor will run on any sinusoidal...

Lube-free Chain exceeds ANSI specs.

Xceeder Chain has oil-impregnated felt seals that keep dirt out and lubrication in for increased wear life. Drive, conveyor, and attachment chains are available in sizes 40 to 100, are interchangeable with ANSI standard chain, and work with standard sprockets. They handle same maximum loads as ANSI standard chain, and exceed ANSI minimum tensile strength requirements.

Servomotor eliminates dithering.

SilverMax 34HC has Anti-Hunt mode which eliminates servo dithering and allows motor to remain motionless while maintaining target position. Motor has 3200 in.-oz of torque, maximum power of 600 W, and is available in 4 stack lengths. System combines motor, controller, driver, encoder, serial communications and 7 configurable I/O. It can be programmed for applications requiring electronic clutch,...

Efficient Motor is for process industry applications.

M3000 motor qualifies for highest European efficiency class (eff1). Improved cooling doubles life of bearings and windings, gives longer component life and protects motor from overheating, even when covered with dust. Large terminal box and terminal board enable easy installation. Motors are available in IEC frame sizes 112 to 400 rated at 4 to 710 kW. Cast-iron enclosure is standard for frame...

Gearing Components fit in small enclosures.

Ultra-flat CSD series harmonic drive gearing component sets use S-shaped tooth profile and are 50% shorter than previous CSF series, allowing surrounding enclosure to be made very compact. It has rated torque of 248 in-lb, maximum torque of 673 in-lb, and is available in gear ratios of 50, 100 and 160:1. Applications include robotics, aerospace, and factory automation.