Fuel Cell Products provide backup power.
Working with hydrogen-fueled ElectraGen(TM) backup power systems, Extended Run Module converts liquid fuel into pure hydrogen to provide power in event of grid failure. System replaces multiple hydrogen cylinders, eliminating need for hydrogen storage when onsite storage is not feasible. Designed for autonomous operation, 250 W portable iGen(TM) proton exchange membrane with on-board fuel...
Read More »
Full-Brick DC/DC Converters have 700 W continuous rating.
Suited for use with RF power amplifiers, RFF series generates regulated intermediate bus voltage in telecom systems with distributed power architecture. Each model produces 28 Vdc output, which can be adjusted over 16.8-29.4 V range. Comprised of 5 isolated models with choice of 2 input voltage ranges and 3 output current ratings, series includes 7-10 Vdc auxiliary output as well as ability to be...
Read More »Mobile VoIP Processor is designed for Wi-Fi-® phones.
Suited for Wi-Fi phones with multimedia and telephony capabilities, BCM1161 integrates ARM9(TM)-based CPU, analog voice codec with direct microphone and speaker interface, as well as interfaces for 262k color LCD display and USB 2.0. Single-chip solution provides polyphonic ring-tone support, 2 Megapixel digital camera, voice record/playback capabilities, and video clip record/playback ability....
Read More »Cable Tray and Support Clamps come in variety of finishes.
Suited for tight installations where access is limited or where cable must be installed close to ceiling or deck, CFL L Wire Cable Tray can be used in conjunction with I-beams or C-beams, allowing beam profile to become part of cable containment pathway. ETC tray beam support clamps attach directly to beam with no need for additional hardware. Available finishes for both include electrozinc, hot...
Read More »
Customized Silicone Technology: For Today's and Next Generation Electronic Applications
This white paper provides and in-depth overview into the customized silicone technology for electronic protection.
Read More »Pneumatic Level Switch features non-bleed design.
Horizontally mounted, float-operated Model 1540 is suited for plant and OEM applications where pneumatic valve operation is required to signal presence or absence of liquid at discrete level. One-piece body and all wetted parts are constructed with 316 stainless steel.
Read More »USB-UART Bridge has highly integrated design.
Requiring 2 external decoupling capacitors for minimal configuration, FT232R includes onboard EEPROM, master clock generator, 3.3 V LDO regulator, reset generator, and USB termination resistors. Integrated device features 5 I/O pins that can be configured in EEPROM to have several functions, including output clock. In addition to full set of modem control signals, each device has variety of...
Read More »
Connectors suit sealed bulkhead applications.
Available in 4, 6, 9, and 12 contact position versions for 20-14 AWG wire, Universal MATE-N-LOK Connectors provide environmental sealing protection to IP56 by employing wire entry seals, interfacial seal, and bulkhead seal. Four-contact position version handles up to 15 A/contact using 14 AWG wire, while 12-position unit handles up to 11 A with 14 AWG wire. Rear mount flange allows connectors to...
Read More »Integrated Circuits suit time-sensitive applications.
ToP (Timing-over-Packet) devices ZL(TM)30301 and ZL30302 transmit timing and synchronization over asynchronous packet switched networks. Both devices maintain average frequency accuracy of under Ã-
Read More »DC/DC Controller powers UltraSPARC-® and SPARC-® processors.
Offering 45 A single-chip solution, PolyPhaseÃ-® synchronous step-down controller, Model LTC3819, features 4 integrated MOSFET drivers and on-board 5-bit digital interface. Core voltage is from 1.025-1.4125 V in 12.5 mV steps and core current ranges from 15-40 A. Housed in 10-pin MSOP package, device operates at up to 90% efficiency from input voltage of 4.5-36 V, and includes current...
Read More »
Step-Down DC/DC Converter comes in 5 x 3 mm DFN package.
Using constant frequency and current mode architecture, LTC3417 operates from 2.25-5.5 V input range and delivers up to 1.4 A continuous output current from one channel and 800 mA from other. This dual-output, synchronous buck regulator can generate 2 independent output voltages as low as 0.6 V, and its adjustable switching frequency from 0.6-4 MHz allows enables use of ceramic capacitors and...
Read More »
Custom Fabrication & Machining Services with Over 30 Years of Experience
As a trusted manufacturer to customers across a broad range of industries, Key Gas Components is a premier provider of CNC machining and tube fabrication. Our entire organization is quality driven and customer-centric, with broad-based manufacturing capabilities that can accommodate the most challenging requirements. See our video to learn more.
Read More »
