New Mechanical Power Transmission Products

Linear Ball Bearings are offered in inch sizes.

Available un-mounted or in aluminum housing, SKF inch series features compact design and recirculating balls to reduce friction and promote unlimited stroke. Series includes open and closed designs in standard or corrosion-resistant versions; self-aligning types; adjustable clearance designs; and tandem linear ball-bearing units. All are equipped with integral seals. Inch-dimension linear ball...

Compact Linear Actuator delivers thrusts up to 50 lb.

Size 14 non-captive, hybrid linear actuator features engineering thermoplastics in rotor drive nut and stainless steel Acme lead screw, which runs axially through center of motor and must be restrained from rotating for proper operation. Suited for long linear travel requirements, actuator offers resolutions from 0.00012-0.00192 in. per step. Typical applications include medical equipment, X-Y...

Assembly System is plug-and-play ready.

ServoPress System, Model 405/4000, features 100% in-process control and monitoring with 180 lb peak load and 115 lb continuous duty load. Industrial servo actuator offers up to 5.9 in. ram stroke and max ram speed of 11.8 ips, while spindle assembly features load cell and mechanical clutch. Equipped with .000004 in. resolution encoder, system uses precision ground ball screw with direct motor...

Die Stamper is available with sensor kits.

Models HCCU-60 and HCCU-150 in Dyne-A-CamÃ-® Nitro-Cam(TM) Series are available with respective sizes of 6Ã-¾ and 16Ã-¾ tons. Products, offered with sensor kits for positioning, can be mounted at any angle in die and retrofit to existing dies. Features include constant force through stroke, built-in mechanical stop for exact cam stroke, and no fluid pressure at die open. Other sizes...

All About Cable Drag Chains

This ebook provides an in-depth overview into cable drag chains.

Magnetically Driven Pumps offer dry-run bearings.

Silicon carbide (SiC-D) bearings, available in MagnatexÃ-® MP, MMP, MPT, and MPH pumps, have surface treatment that reduces friction coefficient and diminishes harmful effect of heat shock during dry-run conditions and start-ups. Chemical-resistant products operate in dry-run condition for 105 min with no cracks or breaks and show no signs of heat-shock damage after operating for 1 hr under...

Diesel Engines range from 240-493 hp.

CURSOR Series consists of 6-cylinder, 24-valve diesel engines that can be configured to meet applications in industrial, agricultural, marine, and power generation industries. Available in 8, 10, and 13 liter versions, engines have total electronic control to monitor operating conditions. Compliant with emission and noise regulations, engines feature noise level below 95 dBA at maximum power....

Micro Gearmotors are battery-powered.

MMP-MGM Series DC Gearmotors, ranging in size from 12-42 mm dia, have compact, fully enclosed TENV design that employs 3, 6, 12, or 24 Vdc windings, depending on model. Suited for battery powered or other low voltage DC applications, products are available with spur or planetary gearing, ratios from 2:1 to 3000:1, and output torques to 4.5 Nm peak. Applications include robotics, portable...

Inverter Duty Gearmotors come in 2 shaft configurations.

Designed for use with adjustable speed controls, gearmotors utilize inverter spike resistant magnet wire for protection against voltage spikes and corona damage. Rated at 3/8 hp, 230 V, 60 Hz, 3-phase, products have operating range of 10-90 Hz and feature gear ratios from 5:1-75:1 for right angle and 5:1-30:1 for parallel shaft configurations. Right angel units feature internal oil expansion...

Grinding Wheels offer custom-matched dressing tools.

Neptune X10 Grinding Wheels come in P-grade in sizes from 8-42 in. and grit sizes from 36-120. Soft, Medium, and Hard bond systems cover range of double disk grinding needs. X10-20, 30, and 35 tool styles contain 3 layers of multi set diamonds, and are suited for wheels up to 20, 30-36, and larger than 36 in., respectively. Single-layer, 7-diamond X10-7 is for 24-36 in. wheels. With diamond...

Gearhead offers 1 arc-min positional accuracy.

Quantum Series Size 14 gearhead is 41 mm long with 73 mm OD. Available in gear ratios of 50, 80, and 100:1, zero-backlash, harmonic drive unit offers rated torque of 89 lb-in., maximum torque of 620 lb-in., and Ã-

Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine

CS Unitec is a leader in power tools designed for industrial applications, with products that set the standard for robust performance and industry-leading reliability. Adding to our long list of innovation is a new line of pipe cutting machines. For cutting and beveling pipe up to 2" in thickness and diameters from 12" to 63", no other cutting system comes close. See our video to learn more.