New Mechanical Power Transmission Products

DC Gearmotor features integral speed control.

Miniature, brushless, 12 V Model LB16-120-BB uses 120:1 spur geartrain to provide rated torque of 3.5 oz-in. at 100 rpm, and achieves continuous load range of 0-6.9 oz-in. Peak torque of 50 oz-in. at 0.8 A is available for starting and accelerating conditions. Input voltage varies from 3.5-13.2 Vdc for variable speed control operation. Measuring 0.63 in. OD x 1.31 in. long, motor weighs less than...

Speed Reducer facilitates hole making in sheet metal.

Operating with most models of handheld electric drills, Holcutter Speed Reducer offers 4:1 gear reduction ratio. It attaches to drills having -½ in. male threaded spindle or to 3/8 in. diameter models with use of adaptor. At working end, reducer features male quad-lead thread mount for attaching 14,000-Series Holcutters without need for intermediary arbor. Speed reducer is suited for...

Hybrid Stepper Motors feature step resolutions of 1.8-º.

MAE(TM) motors provide open-loop control for high-performance positioning applications, delivering step resolutions of 1.8Ã-º in full-step mode. MAE Y Series motors incorporate AlNiCo magnets, N Series motors utilize neodymium magnets, and S Series motors have neodymium magnets. Depending on type, motors range in length from 0.81-9.76 in. and achieve holding torque from 10-3,186 oz-in....

Bearings have chemical-resistant plastic surface.

Fluid-film thrust and journal bearings incorporate engineered plastic surface for use in process-lubricated applications. Bearing pad material is environmentally friendly and can operate directly in water, process fluid, or oil. It provides chemical and wear resistance and tolerates dry start conditions. Mechanical properties such as strength, resistance to creep, and thermal/electric...

Saving Energy with Efficient Belt Drives

By introducing energy efficient belts on electric motor drives, you can implement a simple, cost-effective solution to achieve energy savings in your facility.

Electric Actuator offers 10.02 mm positioning repeatability.

Model RCP2 Robo Cylinder features 73 mm wide aluminum base, 35 x 163 x 68.1 mm controller, ultra-thin head (35 mm), and programmable push force. Electric actuator's controller performs up to 64-point positioning and enables complex movements. Speeds can be changed during slider/rod movement, and positioning repeatability is held to Ã-

Vacuum Motors suit forming and casting applications.

Commercial-grade, VC Series Motors survive pressures as low as 10-6 torr and are available as stepper, hollow-shaft, brushless servo, or rotor nut motors. They are temperature-rated at 130Ã-

Motion Control System is built on step motor technology.

ServoStep(TM) integrated motion control system features 50-pole step motor, motion controller, drive-amplifier, and encoder. NEMA 34 frame size model delivers continuous torque capability of up to 650 oz-in. and nominal speed of 2,200 rpm. Additional features include RS-485 port, closed-loop control, 14 I/O, and 4 kHz PID filter. Able to be used as stand-alone unit, product offers 4 modes of...

Brushless DC Motor is suited for portable applications.

Compact, low-inertia, 12 V, 2-wire motor is available with single- and double-ended shaft configurations. Designed to sustain applications where high-vibration loads are present, motor measures 31 mm in dia x 62 mm long and produces up to 20 W. Electrical and mechanical options include windings for specific power requirements and custom mounting configurations.

Mobile DC Motors suit battery-powered HVAC applications.

PJ and PS series 3 in. dia brush DC motors utilize brush card assembly that improves brush heat dissipation and reduces audible brush noise. They integrate electric noise reduction circuitry and circuit breaker directly within motor housing. PJ design is tube-shell motor with cast end bells, while PS version employs stamped-steel shell. Options include RFI/EMI suppression device that reduces DC...

Actuator features Xenus indexer.

ServoTube actuator makes positioning subsystem for stacking, cutting, pressing, coating, filling, picking, and placing. It requires 50/60 Hz AC power, eliminating need for pneumatic or hydraulic lines. External multi-position thumbwheel switch can call up Xenus' stored motion profile. Continuous force ranges from 51-104 N and peak force is 662 N. Actuator attains 527 m/sÃ-² acceleration and 6...

Precision Machined Parts for High Tech Applications

For precision and value that sets the standard for quality and craftsmanship, EGS Production Machining is the source for precision and value. Our extensive capabilities and dedication to customer service allow us to deliver the optimal manufacturing solution. See our video to learn more.