Receptacles support SCSI and FC-AL systems.
Connectors

Receptacles support SCSI and FC-AL systems.

SCA-2 receptacles consist of staggered contact heights which enable hot-plugging. Alignment guides at both ends house grounding contacts and allow blindmateability. SCA-2 receptacles are installed on backplane to mate directly with SCA-2 plugs installed on disk drive. Tail configurations include through-hole pin and press-fit compliant pin. 80-pin receptacle supports SCSI-3 protocol, while 40-pin...

Read More »
Reverse Expansion Insert presses into plastic hole.
Inserts

Reverse Expansion Insert presses into plastic hole.

Suitable for strengthening plastic joints, Series 18 brass reverse expansion insert is used in applications where bolt enters insert from headless end rather than from headed end. Its head provides high level pull-through resistance and its diamond knurl provides directional torque resistance for bolt installation. Unit does not require any specialized insertion tools, so it can be installed by...

Read More »
Encoders are available with connectors.
Encoders

Encoders are available with connectors.

Accu-Coder(TM) Cube Series and model 702, 725, 758, and 225 encoders are available with Eurofast connector. Connector allows user to reduce stocking requirements for cord sets and similar components since cords can be used for encoder connections and other components of motion control systems (such as proximity sensors and photoelectric switches).

Read More »
RF Edgeboard Connector accepts RG59 or RG6 cables.
Connectors

RF Edgeboard Connector accepts RG59 or RG6 cables.

F Type V-Bite(TM) RF edgeboard connector offers up to -40.3 dB return loss at 2.3 GHz. 75 ohm connector is engineered for signal integrity in RF applications, and snaps and locks into place for secure PCB retention during hand or re-flow soldering. It is supported both above and below board to minimize stress on solder area. Manufactured of machined brass, and employing straight-through contact...

Read More »
PCB Interfaces provides up to 300 I/Os per connector.
Electronic Sockets

PCB Interfaces provides up to 300 I/Os per connector.

FleXYZ interfaces provide flexibility in X, Y, and Z axes by specifying number of rows, pins per row, and desired board spacing with standard interconnects. YTT Series headers and YTW Series board stackers mate with YTQ and YTS Series sockets to provide board spacings from 0.329 to 1.165 in. By using YTE Series elevated socket, board spacing can be increased to 1.705 in. Interconnects have 4-6...

Read More »
Damping Material stops noise and vibration in equipment.
Mounts

Damping Material stops noise and vibration in equipment.

ISODAMP® C-1000 Series thermoplastics, highly damped vinyl materials provide vibration isolation, shock protection and noise control. Three formulations are available as standard and custom-molded isolators. Materials exhibit extremely low amplification at resonance and quick return to system equilibrium after shock or vibration input. ISODAMP C-1002 performs in range from 13 to 41 deg C;...

Read More »
Soft Shell Connectors are available in 2 to 12 positions.
Connectors

Soft Shell Connectors are available in 2 to 12 positions.

Micro MATE-N-LOK 3mm-pitch connectors have dual-beam contacts for improved mating area, and high temperature housings for IR processing. Single row contacts on 3mm centerlines accommodate installations where thin, tight connectors capable of handling up to 5 A are required. Units can provide power and signal I/O and power interface interconnections.

Read More »
Interconnects combine differential and single ended systems.
Connectors

Interconnects combine differential and single ended systems.

Q-Pair high speed interconnects in differential pair configurations allow electrical performance at up to 5GHz operating frequencies. Connectors can be partitioned to include both differential pair and single-ended signal pins, allowing board designer to optimize system for high speed where required, while minimizing impact on density.

Read More »
Anchorage Connector provides temporary fall protection.
Straps

Anchorage Connector provides temporary fall protection.

OSHA-compliant Disposable Concrete Anchor Strap provides secure point of attachment in concrete construction. Strap loop is positioned on rebar and concrete poured over loop and adjoining protective nylon sleeve. Safe anchorage exists once concrete sets. When anchorage is no longer needed, workers simply cut protruding strap. Abrasion-resistant 1 3/4 in. wide nylon webbing, with steel D-ring,...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers