Renesass's New Blood Pressure Monitoring Evaluation Kit Comes with Graphical User Interface (GUI) Tool.
Renesass’s Blood Pressure Monitoring Evaluation Kit consist of pressure sensor, arm cuff, pump, electronically controlled valve, LCD panel, and a reference board. The evaluation kit features RL78/H1D ASSP MCU with analog functions. The unit allows the transmission of data to smartphone via BLE module. RL78/H1D offers 10-bit sequential comparison A/D converters and provides battery voltage...
Read More »
Conta-Clip's New KDS-FP Flange Plate Offers IP66 Ingress Protection
Conta-Clip’s KDS-FP Flange Plate are available in KDS-FP-2x10/24 and KDS-FP-3 x 10/24 models with up to 20 or 30 configurable frame openings respectively. Consisting of 40 x 110 mm duct that is segmented into up to ten frame openings by snapping frame inlays, the inlays are offered in plain partitions, T-pieces or cross and double cross form.
Read More »
New GN 187.4 Stainless Steel Locking Plates are Compliant to RoHS standards.
GN 187.4 Stainless Steel Serrated Locking Plates are adaptable to range of applications. The units are made of different standard steel such as locking plates (American Standard Series 316L), guide housing (AISI 303) and conical thrust springs (AISI 301). The units enable interlocking of standards components at define angle.
Read More »
Heilind Electronics Now Stocking Molex's ValuSeal IP65 Wire-to-Wire Connector System
The Molex ValuSeal Wire-to-Wire Connector System is an IP65-rated, highly reliable sealed connector system. WILMINGTON, MASS. (PRWEB) APRIL 16, 2018 Heilind Electronics, a leading global distributor of electronic components and Molex’s largest authorized distributor in the Americas, has expanded its selection of interconnect solutions with the company’s ValuSeal wire-to-wire connector...
Read More »Fluid Viscous Damping as an Alternative to Base Isolation
Base isolation is an effective way to protect large structures from earthquake damage. This paper asserts that viscous dampers distributed throughout an otherwise conventional structure can also achieve the same result, and at a significantly lower cost. With a theoretical background of fluid viscous damping, this paper describes the installation of viscous dampers in a structure, and provides several examples. It describes fluid viscous dampers, and compares fluid viscous damping and base isolation along with the respective techniques. Design and analysis techniques for fluid viscous dampers are described in detail, and case histories supported by graphical data are also included. The document establishes that fluid viscous damping is a viable alternative to base isolation.
Read More »
Heilind Electronics Now Stocking TE Connectivity's CDFP Connector and Cage Assemblies
CDFP connectors and cage assemblies deliver greater bandwidth and space efficiency WILMINGTON, MASS. (PRWEB) APRIL 12, 2018 Heilind Electronics, a leading global distributor of electronic components and authorized distributor for TE Connectivity (TE), a global leader in connectivity and sensors, announced today the addition of CDFP connectors and cage assemblies to their inventory. With 16...
Read More »
New Radial Loc-N-Load™ Fixture Plate Uses CMM Palletization Features
Radial Loc-N-Load™ Aluminum Fixture Plate is available in 12, 18 or 30 in. rail and plate combinations with 8 in. diameter and 1/2 in. thick black hard anodized aluminum with 1/4-20 threaded holes. The plate comes with laser marked rings for simplifying process of aligning parts. Unit interlocks magnetically and can be installed on all CMMS. The fixture plate allows creation of multiple...
Read More »
Latest M40 Connectors from Harwin are Suitable for Prototyping or Small Volume Runs
Harwin’s new M40 connectors come with phosphor bronze contacts rated for up to 1A. The connectors are lightweight and have low profile at 1mm pitch units. Available in both single and double row options, the connectors can be mounted either vertically or horizontally. Characteristic features are 50 mate/un-mate cycles, insulation resistance of 100MΩ, and operational temperature range of...
Read More »
New Line of Injection Overmold Tooling from ISC Eliminates High Cost of Mechanical Strain Reliefs and Heat Shrink Boots
New line of injection overmold tooling is reliable, robust, and rugged. It has high flex life and comes with an option for embedded electronics. Characteristics features are its biocompatibility, autoclavable nature, and resistance to abrasion and chemicals. Applications include electro surgery, patient monitoring, medical imaging, medical therapy, magnetic stimulation, medical instrumentation,...
Read More »
JW Winco's Stainless Steel Leveling Feet Now Feature an Inlaid Non-Skid Pad
Stainless Steel Leveling Feet bases are offered with (GN 23) and without (GN 21) mounting bores. The units are compliant to RoHS standards and supplied assembled. The leveling feet are made from different standards stainless steel such as base (AISI 304), threaded stud (AISI 303), hex nut (AISI 304, ISO 4032).
Read More »
Senko CS Connector Wins 2018 Lightwave Innovation Award
Senko announced today that the CS Connector was recognized as a winner in the 2018 Lightwave Innovation Reviews program. It was awarded during a reception celebrating finalists and winners on Wednesday March 14, 2018 during the Optical Fiber Conference (OFC). Presented annually by Lightwave, the Lightwave Innovation Reviews program distinguishes top products and solutions available within the...
Read More »
Basalt America Announces Stronger, Lighter, and Corrosion-Free FRP's (Fiber Reinforced Polymers)
Fiber Reinforced Polymers (FRP), represents a truly groundbreaking advancement in structural reinforcement. Lightweight, strong, and green, they are changing the way the construction industry thinks about rebar. Unlike steel, FRPs don't rust and are far stronger than standard rebar. To learn why Fiber Reinforced Polymers are poised to change the way the world builds, see our video.
Read More »
