New Mechanical Power Transmission Products

Grinding Disc handles stainless steel parts.

Tiger Disc provides higher cut rates and has 50-65% more abrasive cloth per disc than conventional zirconium discs. It has abrasive cloth suitable for cool-cutting stainless steel, prevents dulling and glazing of abrasive grains, and has flat configuration for smooth grinding action. Disc is available in 4.5 and 7 in. dia, with and without nuts, and in grit sizes of 60 grit for maximum cut rate...

Slotless Motors are suitable for hand tools and robotics.

Slotless, brushless, DC motors feature slotless stator winding and rotor construction, which provide zero cogging torque and vibration. Stator winding of high density copper positioned inside toothless stator ring creates no preferred rotor position and reduces audible noise. Nominal frame sizes range from 1.4 to 5.8 in. dia, achieving speeds up to 50,000 rpm with torque constants to over 600...

AC Motor is for use in general-purpose applications.

Reliance-® CALIBRE(TM) general-purpose AC Motor is available in horsepower ratings ranging from 3 to 50. Available in horizontal foot-mounted configuration, with optional C Face designs, product is EPAct compliant, and comes with TEFC enclosure in 3600, 1800, or 1200 RPM speeds. It is offered with voltage ratings at 3 Phase, 60 Hertz, or 50-Hertz power systems.

Linear Actuators suit rapid motion applications.

Size 17 hybrid linear actuators are available with 0.9-

How to Select the Right Sprocket for Your Application

This ebook provides overview on how to select the right sprocket.

Worm Gear Drives provide ratios from 1:1 to 60:1.

DAW Series multi-speed transmissions will shift on-the-fly under full load. Model DAW is rated at up to 50 input HP at 1800 RPM and comes in 4 basic configurations. DAW-S is single input with single output shaft; DAW-SD is single input with dual output shafts that may be solid or split; DAW-DS is single input with dual output shafts and output shafts are coaxial shaft-over-shaft; DAW-SI is single...

Servo Motors feature internal Hall sensor feedback.

ELCOM ST(TM) slotted brushless DC servo motors, with 6-slot lamination design, are available in stack lengths of 1/2, 1, 1 1/2, and 2 in. All have 4-pole rotor featuring neodymium iron-bore magnets. Continuous torque output up to 49 oz-in. can be achieved with motor speeds up to 8,000 RPM and power output up to 188 watts. Mounting configuration is consistent with NEMA 23 standards.

Flexible Discs grind and blend in one step.

Cotton fiber layers in Cut-N-Finish discs are impregnated with aluminum oxide grains and then pressed and bonded together, so discs constantly reveal fresh abrasives as they work. Suitable for edge grinding, surface blending, and working fillet welds on stainless steel and aluminum, discs are available in 4 1/2 and 7 in. sizes, and in A24, A36, A54, and A80 grit sizes in both flexible and medium...

Mini Flap Discs work with small air grinders.

POLIFAN(R) flap discs are available in sizes of 2 and 3 in. dia., in flat and conical styles, and in zirconia grain with grit range 24 through 120. Discs are able to grind and finish in one step, and stay aggressive throughout life of disc. Flap discs do not require backing, run cooler, and are suitable for use on all materials.

Direct Drive Motor comes in two parts.

Brushless ULT frameless motor has separate rotor and stator that can be integrated into precision mechanical assemblies. Low profile motor has axial lengths as small as 10 mm, diameters up to 165 mm, and through holes up to 120 mm, making it suitable for direct drive rotary applications. Models are available with 30 to 600 oz-in of torque output. Its three phase motor will run on any sinusoidal...

Lube-free Chain exceeds ANSI specs.

Xceeder Chain has oil-impregnated felt seals that keep dirt out and lubrication in for increased wear life. Drive, conveyor, and attachment chains are available in sizes 40 to 100, are interchangeable with ANSI standard chain, and work with standard sprockets. They handle same maximum loads as ANSI standard chain, and exceed ANSI minimum tensile strength requirements.

Micro Air's Dust, Fume, Mist Collection Equipment Facilitate a Safe Work Environment

Dust, fume, and mist collectors from Micro Air promote a safer, more productive work environment. Our wide array of products are available to the industrial manufacturing sector for processes such as welding, cutting, grinding, blasting, and more. Check out our video to learn more.