Gear Reducer suits rotary positioning applications.

Gear Reducer suits rotary positioning applications.

Hollow-shaft Model RV-C offers through hole ranging from 1.2 to 5.4 in., suitable for allowing vacuum lines, wiring harnesses, concentric shafting, and cooling lines to be run through center. Torsional rigidity and overload torque capacity are rated at 500% of rated torque. Rated torque range is 867 to 27,754 lb-in. with peak torque range of 4,337 to 138,768 lb-in. Total lost motion from all...

Read More »
Digital Linear Actuator is available in two voltage ratings.

Digital Linear Actuator is available in two voltage ratings.

Series 26DBM bidirectional DLA provides linear resolution as fine as .0005 in. per pulse. Suitable for precise, measured control of fluids and gases, modified rotary stepper motor employs rotor that includes internally molded thread that mates to externally threaded shaft. Maximum pull-in rate is 600 step/sec. Series includes 24 models with Ferrite or Neodymium magnets and linear force to 8 lbs....

Read More »
Parallel Gear Drives extend machine functionality.

Parallel Gear Drives extend machine functionality.

Rated at 90% efficient, Add-A-Shaft® parallel gear drives are offered in 1:1, 3:2, and 2:1 ratios with 2 1/4 and 2 1/2 in. shaft centers. Add-A-Shaft® Mini parallel gear drives are 1:1 ratio devices with 1 in. shaft centers. Drives are suitable for packaging, printing, material handling, and assembly machinery, and can be attached or stacked to right-angle gear drives to permit 90 degree...

Read More »
Linear Actuator suits applications requiring rapid motion.

Linear Actuator suits applications requiring rapid motion.

Size 17 Hybrid Linear Actuator is available with extended rotor journal suitable for encoder installation, manual adjustment, or flag installation. Available in captive, noncaptive, and external linear versions, actuator's manufacturing process incorporates engineering thermoplastics in rotor drive nut and stainless steel acme leadscrew. Product line has resolutions from 0.00006 to 0.002 in. per...

Read More »
Parallel Shaft Gearboxes have increased torque capacity.

Parallel Shaft Gearboxes have increased torque capacity.

Models SK 1282 through SK 5382 Clincher(TM) gearboxes have 41% more torque than company's previous models, yet have no gear ratio or dimensional changes. Therefore, engineering revisions by customer are not required to use increased capacity units. Gearboxes are available in 5 case sizes, all with 97% efficiency. Options include torque up to 28,320 lb-in.; power from 0.16 to 30 hp; output speeds...

Read More »
Power Packs suit small/medium-duty truck applications.

Power Packs suit small/medium-duty truck applications.

Available in vented and non-vented designs, hydraulic power pack line offers pumping capacities to 14 gallons per minute and pressures to 2900 psi. Power up and power down designs are available in 12 and 24 Vdc configurations. Series can be used in place of clutch pumps and PTO Ltd.

Read More »
Shaft, Rail, and Bearing Assemblies are offered in 2 metals.

Shaft, Rail, and Bearing Assemblies are offered in 2 metals.

EasyLinear(TM) Express Shaft, Rail, and Bearing Assemblies (SRBs) include guide bar shafts available in steel and stainless steel versions. SRBs can be specified with Teflon® composite bearings with case hardened steel shafting or hard skinned 303 stainless steel shaft. Ball bearings can be specified with case hardened steel shafting. EasyLinear Express SRBs can be cut to length.

Read More »
Linear Thruster withstands torque up to 885 in. lb.

Linear Thruster withstands torque up to 885 in. lb.

DFP combines ball splines and pneumatic cylinders to provide high torque linear thruster. Ball spline doubles as cylinder's piston rod and is preloaded to provide minimal angular deflection of tool plate. Cylinder bore diameters include 10, 16, 25, 32, 50, and 80 mm. DFP thruster is suitable for applications that cannot use larger linear thrusters which utilize tool plate guided by 2 or more...

Read More »
Spline Shafts handle light linear loads.

Spline Shafts handle light linear loads.

Lightweight aluminum spline shafts are suitable for applications that require rotary drive or linear guide. Shafts are treated with low-friction TFE coating and coupled with graphite and PTFE-filled thermoplastic bushing. Coating eliminates need for external lubrication and maintenance. Units are available with basic or anti-backlash bushing; plain or thread mount bushing; and 1/4, 3/8, or 1/2...

Read More »
Chains suit conveyor and equipment-related applications.

Chains suit conveyor and equipment-related applications.

IWIS pre-tensioned chains include MEGAlife maintenance-free roller and conveyor chain, and CR (corrosion-resistant) chain. MEGAlife chain eliminates need for subsequent lubrication, avoiding possible contamination risks to systems and goods associated with chain lubrication in clean or dry environments. CR chain is made from hardened high-alloy steels and offers high strength and fatigue...

Read More »

All Topics