Drum Motor meets MHSA requirements.
Motors

Drum Motor meets MHSA requirements.

Explosion proof 30 hp motor provides safe operation when driving belt conveyors in applications that have potential for fire or explosion, such as mining, feed and grain, sugar mills, and fertilizer plants. Low-profile, 12.5 in. dia motor has heavy-duty bolts; secondary o-ring seal for complete hermetic sealing; standard face width of 51 in.; and cast iron shell, shaft, and end cap. Drum speed is...

Read More »
Gearheads and Gearboxes

Gearboxes raise output torque by up to 47%.

UNICASE(TM) Helical In-Line Gearboxes, from models SK 02 through SK 53, are available in 6 case sizes as single-reduction to sextuple-reduction drives, in foot or flange mounted units. They operate at up to 98.5% efficiency and offer torque up to 19,744 lb-in. Power ranges from .16 to 30 HP; output speeds are from 1 to 986 rpm; and gear ratios range from 1.24:1 to 14340.31:1. One-piece housing...

Read More »
Brake plugs into servo and stepper motors.
Brakes

Brake plugs into servo and stepper motors.

Fail-safe Series SSB incorporates zero-backlash, permanent-magnet brake and torsionally rigid coupling to accept misalignment. Dual bearings allow greater overhung loads created by drive-belt pulleys, chain sprockets, and gearheads. Brake is available in 6 models, for NEMA 23, 34, and 42 sizes. Applications include robotics, linear, and rotary actuators, multi-axis positioning tables, material...

Read More »
Motors

Cooling Tower Motors handle hostile environments.

Epact and NEMA Premium(TM) cooling tower duty replacement motors operate in extreme humidity conditions and corrosive environments. Motors have double-sealed bearings, potted leads, bearing caps on 280 Frame and above, heavy gasketed conduit box and cover, sealed lead openings, sealed bracket-to-frame registers, and umbrella-type seal for shaft-up mounting. Motors are available in 2 to 100 hp....

Read More »
Gearmotors have sealed design to keep oil clean.
Motors

Gearmotors have sealed design to keep oil clean.

Improved right angle single reduction gearmotors are available from 1/2 to 25 hp, in ac and dc. They have internal expansion bladder and Mobil synthetic SHC 634 oil bath lubrication. Because gearmotors are not vented, outside contamination from environment cannot enter and oil stays clean. Other improvements include induction hardened and ground worms for increased life, and castings that...

Read More »
Improved Gearheads handle heavier loads, last longer.
Gearheads and Gearboxes

Improved Gearheads handle heavier loads, last longer.

Stealth PS in-line and RS right-angle helical planetary gearheads have greater face width for higher load capability, smoother tooth engagement, and lower backlash. Stealth Advanced Gearhead has been improved to reduce heat and increase internal lubrication that will extend seal and gearhead life. Other enhancements include smaller viton seals to reduce start up torque and increase efficiency,...

Read More »
Actuators

Screw Actuator drives precision devices.

Miniature Rollnut lead screw actuator converts rotary motion to linear motion or vice-versa in small applications that require precise, repeatable insertion and withdrawal. Roller rides in thread groove for line contact with shaft. Roller rotates in sealed, lifetime-lubricated ball bearings. It can be combined with timing belt drives, sprockets, pulleys, locking and coupling devices, struts and...

Read More »
Laser Measurement Instrument suits alignment applications.
Aligners

Laser Measurement Instrument suits alignment applications.

AlignMeter® simultaneously measures laser beam position and angular displacement for beams up to 8 mm in diameter. Absolute angle and position can be measured with accuracies of 1 mrad and 1 micrometer, respectively, without having to know distance of source from sensor. Results are updated at 10 Hz. It also measures absolute output power from 10 microWatts to 10 mW at wavelengths from 350...

Read More »
DC Motor meets global OEM needs.
Motors

DC Motor meets global OEM needs.

Reliance C500/GS315 provides flexibility to meet either NEMA or IEC dimensional requirements. Four-pole configuration in square, laminated frame improves commutation and heat dissipation. Cast-iron end brackets, with integral mounting feet, put load-carrying members in same vertical plane to eliminate vibration. Motor is available through 800 hp and suits metal, paper, petrochemical, converting,...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers