Miniature DC Motors are 16mm in diameter.
Motors

Miniature DC Motors are 16mm in diameter.

16G88 Series DC ironless-rotor motors have continuous power rating of 4.5 W. They are available with choice of 6 windings for supply voltage from 3 to 24 V. Maximum recommended shaft speed is 12,000 rpm, and typical maximum continuous output torque is 5 mNm. All incorporate precious metal commutators and sleeve bearings. Matching 16mm dia planetary and spur gearheads are available with ratios...

Read More »
Motors

Vertical Pump Motor directly replaces less efficient motors.

Mod-Max meets NEMA premium motor efficiency standards, operates 0.8 to 4.0% more efficiently than company's older, less efficient motors, and can be used for VFD applications. Canopy cap requires no gasket and has 3 stand-offs to allow air circulation to help prevent moisture condensation. Winding includes pulse endurance wire. Each winding is also treated with 100% solids insulation material....

Read More »
Clutch/Brakes start/stop loads to 1/2 deg per revolution.
Clutches

Clutch/Brakes start/stop loads to 1/2 deg per revolution.

CB Series Wrap Spring clutch/brakes, in 5 sizes, have rated static torque ranging from 25 to 2500 lb.in. and 1800 to 300 RPM maximum operating speed. Super CB Series, in 3 standard sizes, has rated static torque from 250 to 2500 lb.in. and 750 to 300 RPM maximum operating speed. Three models of WSC Series clutches are available in 5 sizes with rated static torque from 25 to 2500 lb.in. and 1800...

Read More »
Electric Disc Brakes never require adjustments.
Brakes

Electric Disc Brakes never require adjustments.

Stearns 321 Series consists of 6 totally-enclosed, non-ventilated, armature-actuated electric disc brakes. They are available with static torque ratings of 3, 5, 7, 15, 35 and 50 lb-in. Brakes are designed for service in dirty or contaminated environments to decelerate or hold inertial loads when voltage to brake coil is disconnected. They are available in versions that will operate on 12, 24,...

Read More »
Gearmotors/Speed Reducers operate at 95%+ efficiency.
Motors

Gearmotors/Speed Reducers operate at 95%+ efficiency.

90.1 Series helical bevel gear products are available as triple- or quadruple-reduction drives with foot, flange, or shaft mount configurations. They offer power ranges from 1/6 to 200 HP, output speeds from 0.1 to 218 rpm, torque up to 283,200 lb-in., and gear ratio ranges from 8.04:1 to over 300,000:1. Unicase(TM) housing eliminates oil leakage and contamination. Autovent sealing prevents...

Read More »
Ball Valves and Actuators suit severe duty applications.
Valves

Ball Valves and Actuators suit severe duty applications.

Trunion style ball valves and actuators are specifically designed for shut-off of liquid and gas flow up to 20,000 psi. Two 3-way and 3-way diverter ball valve configurations are available in orifices of .187 or .375 in. Valves incorporate 316 stainless steel construction, Viton 0-rings, Arlon ball seats and peek bearing washers. They have 1 1/16 in. dia hole for panel mounting. Air-operated...

Read More »
DC Motor is suited for light duty belt conveyors.
Motors

DC Motor is suited for light duty belt conveyors.

Micro-Motor 24V brushless DC geared motor has right angle design that fits into 2 3/4 in. conveyor frame. Gearbox transfers 99% of motor output power to belt drive pulley. Driver card controls and activates motor allowing varying conveyor speed and change of travel direction. Micro-Motor has torque rating up to 112 in. lbs and can drive 1.9, 2.25 or 2.5 in. belt drive pulleys. Drive system moves...

Read More »
Gearheads incorporate clamping style input pinion.
Gearheads and Gearboxes

Gearheads incorporate clamping style input pinion.

MRP all-planetary, low-backlash, servo-grade gearheads are available in 1 or 2 stages with ratios up to 100:1. Five sizes are offered: MRP-050, 070, 090, 120 and 155, which range from 2 to 6.1 in. square. Backlash specification is 10 to 15 arc-mins max depending upon gearhead size and number of gear stages. MRP round body gearhead has tapped holes in face of output shaft end, and square flange on...

Read More »
Solids Reduction Unit retrofits to twin shaft grinders.
Bearings

Solids Reduction Unit retrofits to twin shaft grinders.

Annihilator twin shaft solids reduction unit is supplied with seals and bearings housed in replaceable stainless steel cartridge, which allows on-site replacement. Counter-rotating, hexagonal shaft design coupled with hardened steel cutters provide maximum shredding strength necessary to process 300 to 4,250 GPM of influent. Annihilator is fitted with toothed cutting spacers, electronic control...

Read More »
Failsafe Brake fits stepper and servo motors.
Brakes

Failsafe Brake fits stepper and servo motors.

Model RFEB power-off brake mounts on front end of standard NEMA 23 and NEMA 34 stepper or servo motors to prevent machine from operating or for holding load in place when power fails. It has spring-set design, ball bearing supported output shaft, and operates at speeds to 8,000 rpm. Brake is available in 24 and 90 Vdc versions. Applications include factory automation, material handling, robotics,...

Read More »

All Topics