Outer Rotating DC Motor suits high inertia applications.
Motors

Outer Rotating DC Motor suits high inertia applications.

Heavy-duty brushless DC motor has 8.25 in. dia and provides 3.3 hp. Rated at 240 Vdc, motor is available with custom mounting configurations and life-lubricated, double-shielded ball bearings. Capable of developing 960 oz-in. running torque at 3500 rpm, motor is available with high-energy bonded neodymium, bonded samarium cobalt, or ceramic magnets. Magnetic circuit produces low cogging torque...

Read More »
Brake System Kits meet FMVSS 571.121 regulations.
Brakes

Brake System Kits meet FMVSS 571.121 regulations.

Models TA-7000 and TA-8000 Anti-Lock Brake Actuating System Kits fit variety of commercial-duty 1, 2, and 3 axle trailers (weighing up to 45,000 lbs). Electronic control unit relay valve monitors movement of each sensored wheel, thereby modulating air pressure on trailer brakes for sure, controlled stops. Kits are suitable for short run installation and situations where component customization,...

Read More »
Roller Bearings feature optimized roller crown design.
Bearings

Roller Bearings feature optimized roller crown design.

Cylindrical roller bearings are single and double row spindle bearings with crown profile for optimized load distribution. Typically used in combination with double direction angular contact thrust bearings, they are suited for applications where combination of radial stiffness, high radial capacity and high precision support are required. Hybrid Ceramic (HCN) single row cylindrical roller...

Read More »
Support Bearings come in inch and metric sizes.
Bearings

Support Bearings come in inch and metric sizes.

BSB Series (metric) and L-Series (inch) Ball Screw Support Bearings provide axial rigidity, coupled with low friction characteristics, to allow attainment of extreme accuracy during rapid position changes at high speeds. Rigidity is achieved through internal design and built-in universal preload. Cage options include reinforced phenolic (L-Series), or molded nylon, glass fiber reinforced...

Read More »
Spindle Bearings feature non-contacting seal.
Bearings

Spindle Bearings feature non-contacting seal.

Sealed angular contact spindle bearings have non-contacting seal that helps retain lubricant and protects against premature failure caused by infiltration of contaminants. Non-contacting nature of design allows bearings to operate at running speeds up to 1.5 M dN without any impedance normally caused by seal interference. Bearings are offered in high speed (small ball) and standard (large ball)...

Read More »
Gearmotor System is customizable to application needs.
Motors

Gearmotor System is customizable to application needs.

Modular system includes in-line, right angle, and offset gearmotors. Powered by Indrive Variable Speed Gearmotor, Cylindrical Rotor Motors, or Conical Rotor Brake Motors, system offers up to 8,850 lb-ft of torque with horsepowers rated from fractional to 100 hp. Gear drive ratios are available from 3:1 to 500:1 with single or multiple speed motors. Various brake torques are available for stopping...

Read More »
Machine-Tool Bearing provides high corrosion resistance.
Bearings

Machine-Tool Bearing provides high corrosion resistance.

X-Life Ultra utilizes rings made from Cronidur 30 low-nitrogen steel, ceramic (silicon nitride) balls with phenolic cage, thermally stable grease, and integral seal options. Bearing provides 10x longer life when compared to conventional 52100 and 440 hybrid ceramic bearings. Standard bore diameters range from 20 to 120 mm.

Read More »
Gearheads and Gearboxes

Rack and Pinion System offers high linear accuracy.

Rack and Pinion System includes gear reducer or gearmotor with integrated pinion and rack. All mounting surfaces are ground to tight tolerances. Standard rack lengths are 167 to 500 mm. High linear accuracy is due to minimum total pitch error of 12 Â-µm per 500 mm of length. Load capacities up to 13,000 N are available. Wear-resistant surface treatment and individually deburred gear teeth...

Read More »
Stepper Motors have integral fail-safe brakes.
Motors

Stepper Motors have integral fail-safe brakes.

Brakes, coupled to 5-Phase AM Stepper motors, stop heavy loads rapidly and hold them stationary in case of power failure. Holding torque ranges from 41.66 to 138.87 oz-in. Brakes are part of NEMA-size 23 or metric-size 34 package, with dielectric strength sufficient to withstand 0.5 kV at 50 Hz, insulation resistance of 100 Mohms or better, with 500 V potential applied between motor windings and...

Read More »
Thermoplastic Bearing Housings are corrosion-resistant.
Bearings

Thermoplastic Bearing Housings are corrosion-resistant.

Dimensionally stable bearing housings are offered in pillow block and 2- and 4-bolt styles in 204, 205, 206, and 207 sizes. They can be equipped with metal or plastic insert bearings with bore sizes from Â-½ to 1½ in. (12 to 50 mm). Made of solid PBT thermoplastic polyester, they offer tensile strength of 17,300 psi. Able to be cleaned or hosed down with hot water, housings operate...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers