Mounts

Ball Bearings locking device - Torksleeve TSM2

TSM2 offers a mechanical alternative to a conventional mounting of ball bearings to shaft, where assembly time, interchangeability in the field and adjustability is considerably simplified. TSM2 rigidly mounts bearings to shafts, offers infinite axial adjustment, eliminates costly secondary shaft operations, saving production time and cost. The compact and lightweight unit locks in seconds...

Read More »
Motors

Brushless DC Motors feature integrated electronics.

Available in 2-wire and 5-wire versions with operating range of 2-50 W, Models EC 20 flat, EC 32 flat, and EC 45 flat include Hall sensors and 1-quadrant speed controller. In 2-wire version, speed acts proportionately to applied operating voltage of 10-28 V. Current limitation, under and over-voltage switch-off, and temperature monitoring are implemented as standard in all models. Motors are...

Read More »
Motors

Piezo Motor Linear Slide offers speeds up to 8 ips.

Consisting of 4 parts, Model P-653 can replace classical drive elements such as miniaturized motor/lead screw systems or other linear motors. Unit measures 8.0 mm in length with travel range of 2 mm and sub-micron resolution, combined with holding force of 0.15 N. Assembled as unit, moving slider and piezo motor are mounted on PCB driver board requiring 5 Vdc supply. Non-magnetic ceramic motor...

Read More »
Motors

WEG Offers New Family of Rolled Steel Motors

WEG now offers an additional line of rolled steel motors for a broad range of industrial applications. ATLANTA, Georgia, April, 15, 2008 - WEG Electric Motors Corp., a leading global supplier of motors, drives and transformers, has developed a new family of 3-phase motors with rolled steel bodies and cast iron endbells for general industrial use. These new rolled steel motors are available in...

Read More »
Ball Bushing Bearings feature all steel construction.
Bearings

Ball Bushing Bearings feature all steel construction.

Suited for operation in temperatures up to 600Â-ºF, Thomson Stainless Steel A Ball Bushing® bearings deliver travel speeds up to 10 fps and accelerations to 450 fps², without use of derating factors. They have coefficient of friction as low as 0.001 that allows machine builders to use small motors, belts, gears, and ball screws in their machines when replacing high friction,...

Read More »
AC Motor Brakes target stop/hold applications.
Brakes

AC Motor Brakes target stop/hold applications.

Spring-applied UNIBRAKE® AC Motor Brakes include external manual release lever that allows driven load to be moved without energizing motor. Designed for motors that are modified to accept brake mounted to motor's non-driven end, Single C-Face units are available from 3-15 ft-lb. Performing coupling function between standard C-Face motors and C-Face gear reducers, Double C-Face brakes are...

Read More »
Controls and Controllers

Stepping Motor/Driver uses Mechatrolink(TM) II protocol.

Five-Phase MLN50 Mechatrolink Stepper Motor and Driver Network series is 100/200 V AC Driver system that yields full programming command functions and offers communicational data rate up to 10 Mb/s and transmission range up to 50 m max. System measures 120 x 175 x 45 mm and can be empolyed in operational compliancy with patented Mechatrolink Network Controller Bus Communication Motion Link for...

Read More »
Pittman Slotless Brushless DC Servo Motors
Motors

Pittman Slotless Brushless DC Servo Motors

OFFERED IN THREE FRAME SIZES: PITTMAN® SLOTLESS BRUSHLESS DC SERVO MOTORS PROVIDE SMOOTH AND QUIET OPERATION OVER EXTENDED SERVICE LIFE Pittman® slotless brushless DC servo motors provide smooth and quiet operation associated with slotless stator construction and exhibit the extended service life typical with brushless technology. These motors can power a wide range of applications for the...

Read More »
Gearheads and Gearboxes

Bevel Gearboxes offer gear ratios of 1:1 or 1:2.

Available in single and double shaft models, KBX Series Gearboxes can be installed in any direction or orientation. Low-noise units feature aluminum alloy housing and spiral bevel gears in hardened alloy steel case. High-grade grease is sealed into units before shipping so they are maintenance-free. Selective speed ratios with gear ratios of 1:1 or 1:2 make them suitable for most applications.

Read More »
Motors

Pump Controller suits high-pressure hydraulic power systems.

UNiGY® PhD(TM) employs pump-control software to produce precise flow rates and pressures required by application by continually sensing demand and energizing pump only as required, lowering energy consumption, waste heat generation, and noise. Torque regulating drive controller is powered by 100 MHz DSP, which allows compensation in real time for non-linear conditions like fluid...

Read More »
Neagle Choice, LLC Announces New Available Services
Sponsored

Neagle Choice, LLC Announces New Available Services

Neagle Choice has long been known as a quality source for commercial sewing, printing, die cutting, and the manufacturing of a wide range of custom products. Enhancing our service capabilities has been the key to our success, and has driven our growth into many new and exciting markets. Continuing on this trajectory, we now offer precision laser cutting and etching, adding to our long line of manufacturing services. See our video to learn all about it.

Read More »

All Topics