EPDM Compounds suit potable water applications.
Classified by Underwriters' Laboratories to National Sanitation Foundation Standard 61, EPDM Compounds will not leach out when used in manufacture of seals and gaskets for pipes and other conveyors of water.
Read More »Adhesive Transfer Film works in medical gasket fabrication.
BioflexÃ-® Rx477U is an electrically conductive adhesive transfer film used to fabricate gaskets used on medical diagnostic equipment. It features conductive, 2 mil-thick, modified acrylic adhesive that adheres to substrates such as metals, painted surfaces, and plastic films. Transfer film also exhibits chemical-resistance.
Read More »Video Core targets digital television applications.
Model CS7050 high-definition H.264/AVC hardware video decoder core supports wide range of image resolutions, both HD and ST at Main Profile up to Level 4.1. Unit includes direct interfaces to SoC memory control system for storage of reference and decoded pictures in system-wide shared memory. Available on both ASIC and FPGA technologies, core decodes Main Profile video streams at resolutions up...
Read More »Flushing Fluid cleans during start-up and maintenance.
MultiTherm FF-1Ã-® cleans systems during start-up to remove foreign material. Prior to recharging system, it also cleans during general maintenance to remove loose particulate and used heat-transfer fluid. Fluid is compatible with MultiTherm fluids and other fluids.
Read More »
Design & Manufacturing Process of a Coil
Because the design and manufacturing of electromagnets are critical to the successful operation of the application, it's important to spend time defining your requirements before purchasing coils for an application. This eBook will guide you through the process of evaluating the application's constraints, identifying the needed specifications, and collaborating with a manufacturer to develop an appropriate coil solution for the application.
Read More »Heat Transfer Fluid offers oxidation resistance.
Non-toxic, non-hazardous, MultiTherm IG-4Ã-® offers high flash point, low vapor pressure, and temperature range of 10 to 600Ã-
Read More »
Transfer Fluid replaces low-temp silicone-based fluids.
Synthetic Paratherm CR(TM) cryogenic-range transfer fluid provides predictable and repeatable performance in cryogenically driven processes. Fluid properties help eliminate coil freeze-ups. Product offers viscosity of 10 cP @ -88Ã-
Read More »
Power Supply meets ISO7816, ETSI, and EMV standards.
Offered in 16-Lead, 3 mmÃ-² QFN package, LTC4557 dual SIM (subscriber identity module)/Smart card power supply and level translator provides 1.8 and 3 V SIM power and digital signal level shifting. Unit withstands more than 10 kV ESD on all SIM contact pins and has 0.75 mm profile. It contains internal level translators and LDO regulator. Voltage is selected by baseband controller via one pin...
Read More »
PCI Cards are compatible with old and new PCs.
Universal voltage, ARCNET PCI20U network interface modules are compatible with 3.3 V and 5 V computers. Six models link PCI and PCI-X bus compatible computers with ARCNET LAN. Units allow for jumperless configuration and plug-and-play functionality. Each 32-bit, 33 MHz bus card operates with NDIS driver or null stack driver in Windows environment. Two LEDs monitor network operation and bus access...
Read More »
Abrasive Cords and Tapes debur curved surfaces and holes.
Fully impregnated with aluminum oxide or silicon carbide abrasives, cords and tapes are suited for deburring, grinding, and finishing contours, holes, and slots on machined and cast parts. Heavy-duty, flexible products fit into contours and holes inaccessible by files and rigid tools. Abrasive Cords are available in 0.012-0.15 in. OD sizes, and flat tapes measure 1/16-Ã-¼ in. wide. Products...
Read More »
Blackening Gel works on iron and steel substrate parts.
Available in 1 and 5 gal containers and ready for application, PRESTO BLACKÃ-® GEL can be used on any size part in limited quantities. After cleaning part surface, user swabs on layer of product with synthetic paintbrush and allows Gel to work for 2-10 min. Gel adheres to metal surface and blackens uniformly without running off, even on vertical surfaces. Resultant protective black finish...
Read More »
Precision Machining Solutions with Over 25 Years of Experience
Quality, customer service, and unbeatable value are the hallmarks of Hogge Precision. Since 1989 we have built a reputation as the go-to precision machining source, servicing many demanding industries. For CNC machining and screw machining, there are few manufacturers that can match our capabilities and expertise. See our video to learn more.
Read More »
