Conductive Adhesive features low-temperature cure.
Adhesives

Conductive Adhesive features low-temperature cure.

Designed for die attach and general circuit assembly applications, CA-180 cures in 30 min at 80°C,Â- 3 min at 100°C or 10 sec at 150°C with electrical conductivity of 4 x 10-5 ohm-cm. This low-temperature cure conductive adhesive has 48 hr work life and 12,000 cP viscosity at 5 rpm for facilitated needle dispensing or application by pin...

Read More »
Extreme Grip Adhesive eliminates need for nails and screws.
Adhesives

Extreme Grip Adhesive eliminates need for nails and screws.

Suitable for vertical applications, SikaBond® Ultimate Grab bonds to variety of construction substrates, including bricks, glass, metal, concrete, wood, and ceramics. One-component, moisture-cure, instant grab, polyurethane adhesive was developed with Sika's elastic technology, allowing maximum bond flexibility and recovery for long term durable bond. Product is packaged in 10.1 oz...

Read More »
Epoxies

Epoxy Coating suits applications above or below water.

Based on blend of liquid epoxy polymer and aliphatic polyamine curing agents, KALCOAT™ 560 can displace water from wet surfaces to make permanent bond. High build 100% solids epoxy coating is solvent-free and incorporates Kevlar® microfibers for reinforcement and viscosity management for high application rates. KALCOAT 560 can be used as anti-corrosive coating, repair compound, fairing...

Read More »
Paste

Metallization Paste suits high temperature environments.

Designed for mono- and multicrystalline silicon solar cells, SOL205B Back-Side Tabbing Paste optimizes Ag content and glass chemistry to provide consistent adhesion before and after high-temperature ageing. Product is typically dried in IR dryer with set point of 250–300°C in less than 20 seconds. With optimized busbar adhesion, paste contributes to module reliability.

Read More »
How to Choose the Right Adhesive Tape for Your Application
Sponsored

How to Choose the Right Adhesive Tape for Your Application

With a considerable number of adhesive materials, applications and methods, there are many options to consider when choosing an adhesive tape. As NADCO® is a leading manufacturer of custom tapes and labels; we took our years of experience to create this handy selection guide on choosing the right adhesive tape for your application.

Read More »
Matrox at InfoComm 2015 - Product Preview
Cameras

Matrox at InfoComm 2015 - Product Preview

New 4K-over-IP technology, multi-display graphics cards, H.264 encoders/decoders, video wall controller boards, fiber-optic KVM extenders, broadcast streaming and recording appliance, and multi-camera recording app to be showcased MONTREAL –Â- Matrox® Graphics Inc. and Matrox Video will be sharing booth 4053 at InfoComm 2015 (Orlando, June 17-19). Matrox Graphics Inc. will present a...

Read More »
Sealing Equipment

Nelipak Healthcare Packaging to Showcase Thermoformed Medical Packaging Solutions at Medtec Europe

Package Integrity Testing as an Important Tool in Determining the Sterility and the Shelf Life of a Medical Device or Product” Session presented by Nelipak to be held on April 23rd WHO: Nelipak® Healthcare Packaging ("Nelipak"), a global provider of custom thermoformed packaging that provides superior protection for medical devices and pharmaceuticals. Nelipak custom thermoformed medical...

Read More »
Paste

Heraeus to Attend SNEC 2015

Heraeus announces new products and activities in China SHANGHAI –Â- The Heraeus Photovoltaics Global Business Unit will be attending the SNEC 9(th) (2015) International Photovoltaic Power Generation Conference Exhibition from April 28(th) through April 30(th), 2015. Heraeus will highlight several of its newest products, including additions to their SOL9621 Series of front-side...

Read More »
UV Cure Adhesive suits circuit assembly applications.
Epoxies

UV Cure Adhesive suits circuit assembly applications.

Designed to cure rapidly when exposed to high-intensity UV light, 535-11M-7 Epoxy is suitable for lens bonding in camera modules, chip encapsulation in smart cards, and variety of general bonding applications in photonics assembly. Flexible, high-strength epoxy adhesive is non-conductive, low-outgassing, and does not contain antimony.

Read More »
Additives

Total Cray Valley to Showcase Novel Additives for High-Performance Thermoplastics at 2015 Compounding World Congress

EXTON, Pa. – Global functional additive manufacturer Total Cray Valley today announced that it will be exhibiting several novel additives for high-performance thermoplastic formulations at this year's Compounding World Congress. Cray Valley's plastic formulation specialists will be showcasing the company's Dymalink® coagents and Cleartack® resins during the tabletop...

Read More »
High-Temperature Sealant suits applications to 950°F.
Sealants

High-Temperature Sealant suits applications to 950°F.

Formulated by combining high-temperature resin with ceramic fibers and powders, Pyro-Putty™ 950 can be used as gasketing compound for boilers, compressors, heat exchangers, furnaces, ovens, and exhaust manifolds. Product repairs rough, scored, or irregular surfaces and is resistant to chemical and steam attack, high pressure/vacuum atmospheres, mechanical vibration, and joint movement. Offered...

Read More »
Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine
Sponsored

Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine

CS Unitec is a leader in power tools designed for industrial applications, with products that set the standard for robust performance and industry-leading reliability. Adding to our long list of innovation is a new line of pipe cutting machines. For cutting and beveling pipe up to 2" in thickness and diameters from 12" to 63", no other cutting system comes close. See our video to learn more.

Read More »

All Topics