Stratasys Additive Manufacturing Solutions Selected by Airbus to Produce 3D Printed Flight Parts for Its A350 XWB Aircraft
Resins

Stratasys Additive Manufacturing Solutions Selected by Airbus to Produce 3D Printed Flight Parts for Its A350 XWB Aircraft

Minneapolis Rehovot, IsraelÂ- — Stratasys Ltd. (Nasdaq:SSYS), a leading global provider of 3D printing and additive manufacturing solutions, announces that leading aircraft manufacturer Airbus has produced more than 1000 flight parts on its Stratasys FDM 3D Production Systems for use in the first-of-type A350 XWB aircraft, delivered in December 2014. The 3D printed parts were used in place...

Read More »
Calibrators

Terpenes Standards for Medical Cannabis Analysis Just Released by Restek

Restek is pleased to announce the release of new multicomponent terpenes standards for medical cannabis analysis. These new blends contain the most important terpenes for cannabis labs and are formulated for maximum stability. High-concentration (2,500 Â-µg/mL) solutions provide value and maximize flexibility, so labs spend less time preparing standards and more time analyzing samples....

Read More »
Rectifiers and Diodes

Bayer Polycarbonate Resin, Sheet and Films Satisfy Design and Performance Requirements of LED Lighting Market

NEW YORK - LED lighting is experiencing increased adoption in many residential and commercial applications, and customers are demanding more energy-efficient options without sacrificing design. To meet these needs, Bayer MaterialScience LLC offers a portfolio of polycarbonate resin, sheet and film materials for LED lighting applications that satisfy a variety of design and performance...

Read More »
Conductive Adhesive features low-temperature cure.
Adhesives

Conductive Adhesive features low-temperature cure.

Designed for die attach and general circuit assembly applications, CA-180 cures in 30 min at 80°C,Â- 3 min at 100°C or 10 sec at 150°C with electrical conductivity of 4 x 10-5 ohm-cm. This low-temperature cure conductive adhesive has 48 hr work life and 12,000 cP viscosity at 5 rpm for facilitated needle dispensing or application by pin...

Read More »
Sealing Equipment Buying Guide
Sponsored

Sealing Equipment Buying Guide

Can't tell the difference between all the different types of sealing equipment? Download this informative sealing equipment buying guide to learn the types, methods, and applications that are available to you.

Read More »
Extreme Grip Adhesive eliminates need for nails and screws.
Adhesives

Extreme Grip Adhesive eliminates need for nails and screws.

Suitable for vertical applications, SikaBond® Ultimate Grab bonds to variety of construction substrates, including bricks, glass, metal, concrete, wood, and ceramics. One-component, moisture-cure, instant grab, polyurethane adhesive was developed with Sika's elastic technology, allowing maximum bond flexibility and recovery for long term durable bond. Product is packaged in 10.1 oz...

Read More »
Epoxies

Epoxy Coating suits applications above or below water.

Based on blend of liquid epoxy polymer and aliphatic polyamine curing agents, KALCOAT™ 560 can displace water from wet surfaces to make permanent bond. High build 100% solids epoxy coating is solvent-free and incorporates Kevlar® microfibers for reinforcement and viscosity management for high application rates. KALCOAT 560 can be used as anti-corrosive coating, repair compound, fairing...

Read More »
Paste

Metallization Paste suits high temperature environments.

Designed for mono- and multicrystalline silicon solar cells, SOL205B Back-Side Tabbing Paste optimizes Ag content and glass chemistry to provide consistent adhesion before and after high-temperature ageing. Product is typically dried in IR dryer with set point of 250–300°C in less than 20 seconds. With optimized busbar adhesion, paste contributes to module reliability.

Read More »
Matrox at InfoComm 2015 - Product Preview
Cameras

Matrox at InfoComm 2015 - Product Preview

New 4K-over-IP technology, multi-display graphics cards, H.264 encoders/decoders, video wall controller boards, fiber-optic KVM extenders, broadcast streaming and recording appliance, and multi-camera recording app to be showcased MONTREAL –Â- Matrox® Graphics Inc. and Matrox Video will be sharing booth 4053 at InfoComm 2015 (Orlando, June 17-19). Matrox Graphics Inc. will present a...

Read More »
Sealing Equipment

Nelipak Healthcare Packaging to Showcase Thermoformed Medical Packaging Solutions at Medtec Europe

Package Integrity Testing as an Important Tool in Determining the Sterility and the Shelf Life of a Medical Device or Product” Session presented by Nelipak to be held on April 23rd WHO: Nelipak® Healthcare Packaging ("Nelipak"), a global provider of custom thermoformed packaging that provides superior protection for medical devices and pharmaceuticals. Nelipak custom thermoformed medical...

Read More »
Paste

Heraeus to Attend SNEC 2015

Heraeus announces new products and activities in China SHANGHAI –Â- The Heraeus Photovoltaics Global Business Unit will be attending the SNEC 9(th) (2015) International Photovoltaic Power Generation Conference Exhibition from April 28(th) through April 30(th), 2015. Heraeus will highlight several of its newest products, including additions to their SOL9621 Series of front-side...

Read More »

All Topics