Isolation Valve reduces possibility of leakage.

Series 462 Resilient-Seal 3-way inert isolation valve utilizes soft FFKM (KalrezÂ-®) disc within PTFE diaphragm to create tight seal. Highly inert materials such as PTFE, PEEK, and FFKM make it suitable for handling aggressive reagents or high purity media found in analytical instrumentation. Internal volumes and dead volumes are also minimized to avoid contamination and reagent waste. Valve...

Read More »
Lift Axle Control increases air flow.

Lift Axle Control increases air flow.

AKAD1001 lift axle air control kit is approved for use with INTRAAX-® and HT SERIES liftable suspensions. Kit comes with ball valve, pilot valve, solenoid valve, gauge, and regulator fitted in fiberglass reinforced enclosure. Pilot ports and potential water traps face down or are placed above exhaust ports to help prevent water from collecting. Air control was tested from -40 to 180-°F.

Read More »
Directional Control Valve comes complete with electronics.

Directional Control Valve comes complete with electronics.

Model 4DP01 proportional valve has factory-set, top-mounted amplifier electronics, allowing repeatability from valve to valve, and minimizing setting procedure in field. Non-conductive electronics box is suitable for food processing applications, where frequent wash downs are required. Other applications include plastic injection molding machines, extrusion presses, die-casting machines, conveyor...

Read More »
Dispense Valve applies precise amounts of UV-cure adhesive.

Dispense Valve applies precise amounts of UV-cure adhesive.

Pneumatically operated Model 752V-SS has no seals or O-rings to wear out and leak. Diaphragm is rated for tens of millions of cycles. Drip-free cutoff eliminates waste. Adjustable stroke control allows flow rate to be fine tuned, while microprocessor-based VALVEMATE(TM) controller allows open time to be adjusted in increments from 0.01 to 0.001 sec. Valve is suitable for automated assembly...

Read More »
Globe Valve has zero-leakage design.

Globe Valve has zero-leakage design.

Series 5080 Manual Globe Valve offers pressure range of 0 to 6,000 psi and can be used in metering, throttling, or full open or closed operation. Encapsulated plastic seat protects against wire drawing. Teflon seat and 316 stainless steel body assure compatibility with most gases and liquids. Sizes are 3/4 and 1 in., with Cv of 3.79 and NPT or MS33649 tube connections. Ambient and cryogenic...

Read More »
Isolation Valve measures less than 1 in. long.

Isolation Valve measures less than 1 in. long.

Micro-miniature Model 218 inert 2-way solenoid-operated valve is 3/8 in. in total diameter. It features manifold interface design, requiring no locating pins. Valve has TeflonÂ-® and Peek body for chemical resistance, making it suitable for corrosive gases and fluids. It is rated at 30 psi and provides flow rates of 405 cc/min @ 30 psi with water. Coil configurations include 24 Vdc 1.2 W or...

Read More »
Check Valves are suited for vacuum operations.

Check Valves are suited for vacuum operations.

Vacuum check valves work with venturi vacuum pumps and switches to seal and maintain vacuum levels. With cracking pressure rated at less than 1 in. Hg., they allow air flow in one direction only. Valves can be manually operated or automatically controlled by vacuum switch. Able to be used in any orientation, valves come in 1/4 and 3/8 in. NPT sizes and are made of chrome plated brass with...

Read More »
Safety Valve offers pull ring for testing.

Safety Valve offers pull ring for testing.

Figure 15LC Safety Valve is ASME Section VIII UV certified and is suitable for bulk hauling railroad and truck tank cars. It provides tight shutoff, sharp popping and closing action, and repeatability. Proper alignment of seating surfaces is assured by integral inlet and body casting. Its threaded 2 in. aluminum body handles pressures from 5 to 15 psi and temperatures to 250Â-

Read More »
Control Valve converges and diverges liquid flow service.

Control Valve converges and diverges liquid flow service.

Class DOT 3-way control valve has one-piece body construction with spring-loaded Teflon chevron stem packing that eliminates need for periodic adjustment. Cage-guided trim reduces stem load and adds to valve stability; there is no need to remove DOT from line to replace trim. Control valve is available with cast iron or bronze body in 1 through 3 in. sizes. It is offered with threaded or flanged...

Read More »
Valve provides precision fluid transfer in syringe system.

Valve provides precision fluid transfer in syringe system.

Dual solenoid, 3-way valve features rectangular design capable of switching on demand to allow independent operation of each inlet port. Four possible on/off configurations between normally-open and normally-closed ports include both on, both off, on/off, and off/on. Valve can be assembled on top of multiple syringes, and mounted side-by-side while functioning in traditional aspirate and dispense...

Read More »

All Topics