Masterbatches minimize scrap in injection molding process.
Intended for use with engineering thermoplastics, Performance Plus(TM) color and additive masterbatches are formulated to lower resin viscosity during processing and optimize pigment and additive distribution. Lower viscosity allows injection molders to shorten cycle times by processing at lower temperatures. Masterbatches are not reactive or toxic, do not migrate, and are safe in all forms of...
Read More »Desiccant Additive extends packaging shelf life.
Intended for use in translucent and opaque films made of low density and linear low density polyethylene, Masterbatch Product 101499 protects packaging from moisture penetration. It reacts with and binds water vapor as it enters film, extending shelf life of foods and pharmaceuticals. Compound can be used in blown and cast films, whether monolayer or multilayer, and complies with federal...
Read More »Additive makes LLDPE film clearer than base resin.
High-clarity slip antiblock, Product 102286 eliminates loss in clarity that often accompanies antiblock use by raising film clarity well above that of base resin. Product makes film up to 65% clearer 50% more glossy than base polymer. Mineral-based additive has narrow particle size distribution and spherical particles that have less impact on haze than irregular particles normally found in agents.
Read More »
Rare Earth Plate Magnets offer surface strength of 8,000 G.
Xtreme(TM) Magnets utilize double stack of magnet pressings and can be used in operations where ferrous extraction is required. They can remove fines, work-hardened stainless steel, and weakly magnetic materials in food and pharmaceutical applications. Magnets are designed to perform in situations with deeper burden depths, higher suspension heights, deep reach applications, and U-Trap...
Read More »
All About Cable Drag Chains
This ebook provides an in-depth overview into cable drag chains.
Read More »
Adhesive Film adheres to silicone-coated substrates.
Designed to bond silicone substrates and other difficult-to-bond materials, Scapa 706 features specially treated polyester release film with operating temperature range of -55 to +400Ã-
Read More »Interface Module facilitates DAQ system communication.
Computer interface Model CP22 complements MGCplus multi-channel data acquisition system by allowing rapid communication from sensors. In addition to RS232 serial link, unit includes TCP/IP, 10/100 Mbit Ethernet interface, which allows transmission of over 150,000 measured values/sec, across 64 channels, each operating at 2.4 kHz sample rate. USB 1.1 interface enables transmission of more than...
Read More »
Controller Card is 32-bit/33 MHz PCI bus compatible.
PCI IEEE 488 Controller Card, Model PCI-3488 provides interface between GPIB instruments and PCI-equipped systems that is compliant with IEEE488.1 and IEEE488.2 standards. Interface supports 3.3 and 5 V PCI environments, making card suited for most desktop computers and industrial PCs. Featuring 1 Kb on-board FIFO and high-speed bus accelerated by on-board CPLD, Model PCI-3488 provides 1.5 Mb/s...
Read More »
Permanent Magnets lift heavy, complex work pieces.
Able to handle round and flat materials, SafeHoldÃ-® RPL-35 and RPL-70 can lift and transfer steel and iron without slings, hooks, or cables. Magnets do not require power supply, and internal on/off changeover mechanism eliminates possible scratches on work surface when loading or unloading. Models RPL-35 and RPL-70 feature capacities of 3,500 and 7,000 lb for flat materials and 1,750 and...
Read More »
Teflon-® Tape ranges from .020-.125 in. thick.
Fat Teflon-® Tape is conformable, non-reinforced skived tape with pressure sensitive adhesive on one side. Product is non-porous, self-lubricating, chemical and moisture resistant, and resistant to extreme temperatures from -100 to 400-°F. Offered in 5 or 36 yd rolls, tape comes in widths from -½-12 in. and is available with High Temp Silicone or Acrylic Adhesive. Typical uses include...
Read More »
560 and 572 Series IP67 Waterproof Inline Plug and Socket Connectors with Shock and Vibration Resistance
EDAC's new line of IP67 waterproof plug and socket connectors represent the cutting edge of waterproof connection technology. Part of the 560 and 572 series of connectors, they utilize innovative design concepts to deliver a level of performance and value that is unmatched in the industry. See our video to learn more.
Read More »
