Epoxies

Epoxies

Epoxy Adhesive is NASA outgassing approved.

With working life of 60 min, black medium-viscosity TRA-CAST 3145 can be cured in 24 hr at ambient temperatures or more quickly at elevated temperatures. Product is thermally conductive, electrically insulating, and suitable for staking transistors, diodes, resistors, ICs, and other heat-sensitive components in PCB applications. TRA-CAST 3145 has 100% reactive solids content, offers Shore D...

Read More »
Epoxies

Adhesive combines epoxy and light cure chemistries.

Loctite® 3355(TM) works on colored and opaque substrates such as metals, plastics, glass, and ceramics that cannot transmit light. Once dispensed onto opaque part, exposure to UV light at 254-365 nm for 5-60 sec activates adhesive, which cures to fixture strength in minutes and reaches full cure in hours at room temperature. Single component, medium viscosity product requires no mixing,...

Read More »
Epoxies

Epoxy Adhesive passes NASA outgassing tests.

With operating temperature of 4°K to 400°F, thermally conductive, electrically insulative EP21TCHT-1 cures at room temperature or more rapidly at elevated temperatures. It features mix ratio of 100:60 by weight and mixed viscosity of light paste. Product is 100% reactive and does not contain solvents or diluents. It adheres to metals, ceramics, glass, wood, vulcanized rubbers, and...

Read More »
Epoxies

Flexible Epoxy dispenses with pinpoint accuracy.

Supplied in hand-held applicator, 400°F Duralco 125 cures at room temperature to provide electrical conductivity, thermal and mechanical shock resistance, adhesion to dissimilar substrates, and chemical resistance. No mixing or measuring is required. Adhesive is suited for manufacture and repair of flexible circuits, solder replacement, bonding semiconductors, EMI shielding, bonding...

Read More »
Encapsulants

Epoxy Potting Compound has mixed viscosity of 6,700 cp.

Targeted for electronic assembly manufacturers, 2-part 20-3063 epoxy potting and encapsulating compound has 1:1 mix ratio with resin pigmented black and catalyst white for visual indication that products have been properly mixed. It cures at room temperature to 75-80 Shore D hardness, has 45 min pot life, usable temperature range of -40 to 130°C, and dielectric strength of 450 V/mil.

Read More »
Epoxy Adhesive resists exposure to repeated sterilization.
Epoxies

Epoxy Adhesive resists exposure to repeated sterilization.

Resistant to thermal shock, EP45HT MED is formulated for use in assembly of reusable medical devices. This 2-component epoxy adhesive requires min heat cure of 250°F and withstands exposure to repeated cycles of radiation, steam (autoclaving), and chemical sterilants. Able to handle long-term exposure to temperatures from -80 to +500°F, cured system acts as electrical insulator and...

Read More »
Epoxy Adhesive offers flexible cure.
Epoxies

Epoxy Adhesive offers flexible cure.

Nickel-filled, 2-component EP21TDCNFL is 100% reactive and does not contain solvents or volatiles. Product is prepared using 1:1 mix ratio by weight or volume, and once cured, has volume resistivity of less than 5-10 Ω/cm and tensile lap shear strength of 2,000 psi. Temperature range of 4°K to 250°F makes adhesive suited for cryogenic applications. Bonds offer thermal resistance as...

Read More »
Compound suits potting and encapsulation applications.
Encapsulants

Compound suits potting and encapsulation applications.

Two-component Master Bond EP30DP epoxy/urethane elastomer can be cast in thick cross sections without development of undue exotherm during cure. With service operating temperature of -80 to +250°F, product is formulated to cure at room temperature or more rapidly at elevated temperatures. Cured compound offers abrasion resistance and electrical insulation. Polymer system has Shore A...

Read More »
Flexible Plastic Bonder has thixotropic formulation.
Epoxies

Flexible Plastic Bonder has thixotropic formulation.

With 1:1 mix ratio and Shore D hardness of 65, TRA-BOND 2170T suits applications that require chemical fastening to plastic parts. Amber epoxy adhesive bonds nylon, PVC, polyethylene, acrylic, lexan, polypropylene, kapton, and other thermoplastic substrates. Featuring working life of 2 hr, product and can be cured in 24 hr at room temperature or at accelerated rate in 65°C heat. Industries...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers