Epoxies

Adhesive/Sealant offers long-term storage capability.
Epoxies

Adhesive/Sealant offers long-term storage capability.

Master Bond Polymer System Supreme 10HTFL is single-component, epoxy resin-based adhesive/sealant with -300 to +300°F service temperature range. Cured to flexible thermoset polymer at temperatures of 250-300°F and above, product does not require refrigeration for extended storage before use. It adheres to metallic and non-metallic substrates, even upon prolonged exposure to hostile...

Read More »
Thermally Conductive Epoxy works in temperatures to 400°F.
Epoxies

Thermally Conductive Epoxy works in temperatures to 400°F.

Suited for bonding applications, Aremco-Bond(TM) 860 aluminum nitride-filled, electrically insulating epoxy adheres to high-temperature plastics as well as glass, ceramic, and high-expansion metals. This 2-component, 100% solids material has 1:1 resin to activator mix ratio and cures in 24 hr at room temperature or 2 hr at 200°F. After curing, it exhibits thermal conductivity of 8.5...

Read More »
Sealant has -300 to 600°F service temperature range.
Epoxies

Sealant has -300 to 600°F service temperature range.

One component, heat curing epoxy adhesive/sealant EP17 cures at temperatures from 300-350°F for 60-90 minutes. Flowable paste has 8,700 psi tensile strength, 387,000 psi tensile modulus, Shore D hardness greater than 90, and compressive strength greater than 13,000 psi. MIL-MMM-A-132 compliant, 100% reactive compound is resistant to chemicals, including fuels and acids, and bonds to metals,...

Read More »
Two-Part Epoxy features low exotherm during cure.
Polymers

Two-Part Epoxy features low exotherm during cure.

Master Bond Polymer System EP37-3FLSP bonds to substrates such as metals, glass, ceramics, plastics, and elastomers. Optically clear epoxy features electrical insulation properties and exhibits resistance to vibration, shock, and thermal cycling. Suited for large-volume castings, product has 20 Shore D hardness, 1,000 psi tensile strength, and over 400 V/mil dielectric strength. Pot life after...

Read More »
Epoxy Adhesive meets NASA low outgassing specifications.
Epoxies

Epoxy Adhesive meets NASA low outgassing specifications.

Formulated to setup in 3-5 min in 10-20 g masses at room temperature, EP65HT-1 ultra-fast curing, high temperature resistant epoxy adhesive bonds with metals, glass, ceramics, woods, vulcanized rubbers, and plastics. It has Shore D hardness of >75 and volume resistivity of >1014 ohm-cm. Mixed viscosity is 60-70,000 cps and mix ratio is 10 to 1 by weight. Available in pint, quart, gal, and 5 gal...

Read More »
Epoxies

Adhesive and Epoxy are designed for flip chip assembly.

Material GPC-251A/B is silver-filled, electrically conductive, 2-part, room-temperature curing adhesive used to connect bumps on underside of circuit boards. Product cures in 24 hr @ 25°C, 60 min @ 65°C, and 5 min @ 120°C. Material 123-38A/B-187 is thermally conductive underfill epoxy that strengthens chip package, protecting it from moisture and adding mechanical strength....

Read More »
Repair Epoxy forms machinable aluminum layer.
Epoxies

Repair Epoxy forms machinable aluminum layer.

Packaged in pre-measured job sized kits, 450°F Machine-IT features sticky consistency that holds assemblies or parts together while curing. Product offers adhesion to smooth, rough, or porous surfaces, and most plastics, metals, ceramics, glass, and wood. Curing in 2-4 hours, epoxy forms hard, metallic composite that can be machined, tapped, drilled, and threaded. Machine-IT is suited for...

Read More »
Repair Compounds

Low Viscosity Adhesive offers Tg of 90°C.

TRA-BOND F110 is optically clear, low viscosity adhesive. Two-part epoxy can be room temperature or heat cured, and provides thin bond line on applications involving prisms, lenses, and other optical components. Adhesive exhibits wicking and wetting characteristics, offers high strength structural bond, and bonds to glass, ceramics, metals, and most rigid plastics.

Read More »
Epoxies

Epoxy Adhesive features low viscosity.

TRA-BOND F113SC epoxy adhesive is formulated for fiber optics, LED displays, lenses and other optical components. It provides high bond strength and low stress connections with no pistoning. Featuring Tg of 95°C, 2-part rigid epoxy system is curable at room temperature or can be heat cured in 15 min. It exhibits low water absorption percentage.

Read More »
Epoxies

Epoxy Adhesive has tensile shear strength of 2,000 psi.

Two component, room temperature curing, nickel filled, electrically conductive EP76M epoxy adhesive features thermal conductivity of 8-9 Btu/in/ftÂ-²/hr/°F. Featuring one to one mix ratio by weight or volume, it offers 5-10 ohm-cm volume resistivity. EP76M exhibits 30 in/in x 106/°C thermal expansion coefficient, and service operating temperature range of -60 to +250°F....

Read More »
Basalt America Announces Stronger, Lighter, and Corrosion-Free FRP's (Fiber Reinforced Polymers)
Sponsored

Basalt America Announces Stronger, Lighter, and Corrosion-Free FRP's (Fiber Reinforced Polymers)

Fiber Reinforced Polymers (FRP), represents a truly groundbreaking advancement in structural reinforcement. Lightweight, strong, and green, they are changing the way the construction industry thinks about rebar. Unlike steel, FRPs don't rust and are far stronger than standard rebar. To learn why Fiber Reinforced Polymers are poised to change the way the world builds, see our video.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers