Epoxy Meets Airbus Standards for Flame Retardancy, Smoke and Gas Emissions
Formulated to meet rigorous Airbus specifications, Master Bond EP93FRHT passes the twelve second vertical burn test per AITM 2.0002B and Section 7.1.2 of ABD0031, Issue F; the smoke emission test per AITM 2.0007B, Issue 3 in the flaming mode and Section 7.3.2 of ABD0031, Issue F; and the toxic gas emission test per AITM 3.0005, Issue 2 in the flaming mode and Section 7.4 of ABD0031, Issue F....
Read More »Encapsulant Adhesive Paste reflows at 230°C.
Offering pull strength up to 180g at room and high temperatures, SMT 256EP Encapsulant Adhesive Paste improves solder joint strength. Used for mass production via dispensing or printing, unit is suitable for high temperature applications up to 300°C and package level applications.
Read More »
High Strength Epoxies for Plastic Bonding
Lap shear strength is one of the most common stresses that a bonded joint can face, especially in structural bonding applications. It is tested by measuring the ability of an adhesive system to withstand stresses set in a plane, where the exerted shear force is moving the two substrates in opposite directions. This article evaluates select Master Bond epoxies that were recently tested for their...
Read More »
70-3812NC Epoxy Adhesive meets ASTM E-595-07 standards.
Providing enhanced bonding and thermal conductivity, 70-3812NC Aluminum Filled Epoxy Adhesive is suitable for bonded fin heat sink and pipe bonding in extruded aluminum base applications. Formulated to be cured at room temperature or with mild heat, product’s 10:1 mix ratio is easy for batch mixing or using Meter Mix and Dispense Equipment.
Read More »
A Kickstart Guide to Cyanoacrylates
This eBook provides a guide to Cyanoacrylate instant adhesives.
Read More »
Uni-Seal™ 6322: UV / LED / Visible Hybrid Low Shrinkage (Soft) Gasketing Sealant / Bonder
Incure Uni-Seal™ 6322 UV / Visible / LED light curable adhesive is an acid-free, low viscosity form-in-place / cure-in-place gasket (FIPG / CIPG). Cures very fast with low energy LED lamps for high volume production. High resilient (good memory retention) and high flexibility out-perform many gaskets provides air-tight sealing. Uni-Seal™ 6322 exhibits enhanced excellent moisture and...
Read More »
Adhesives for Your Specific Needs
EP30Med: Low Viscosity Epoxy Meets USP Class VI Specifications Ideal for encapsulation, bonding and sealing applications, EP30Med offers excellent electrical insulation properties and exceptionally low shrinkage upon cure. It is a two component, room temperature curing biocompatible epoxy adhesive designed for high performance medical device applications. It features high bond strength, superior...
Read More »
Cera Mastic Refractory Putty dries at room temperature.
Used for patching, repairing and filling fissure, Cera Mastic Refractory Putty offers adhesion to refractory types without chipping or flaking. Providing tough repaired surfaces over temperature range of 500°C to 1500°C, unit does not contain refractory ceramic fiber. Product is not sensitive to freezing and exhibits no sintering, shrinkage, or cracking with thermal cycling.
Read More »
SCProbond™ Adhesives are non-corrosive epoxy system.
Formulated to adhere ceramic components in material handling, power generation, mining and petroleum industries, SCProbond™ Epoxy Adhesives are available in low (LV-1) and high viscosity (HV-1) versions. SCProbond™ LV-1 is used in installing components in horizontal applications whereas SCProbond™ HV-1 is designed for vertical and overhead tilting applications. Product features good...
Read More »
Two Component, Low Viscosity Epoxy Features Outstanding Chemical Resistance
Master Bond EP62-1BF is a two part epoxy featuring the ability to withstand exposure to aggressive chemicals including acids, bases and solvents, even at high temperatures. “We tested the chemical resistance properties of EP62-1BF by taking cured samples of the system and immersing them in a variety of chemicals, like sulfuric acid, toluene, ammonium hydroxide, etc.,” said Venkat Nandivada,...
Read More »SCProbond™ A/CRC Wear Compound is corrosion resistant.
Resisting chemical attack and sliding abrasion, SCProbond™ A/CRC Wear Compound is suitable for mining, construction, petrochemical, power generation and manufacturing operations. Compound can be applied as a protective layer in pump housings, elbows, hoppers, cyclones and dust collectors. Product is designed as an easy to mix and apply wear liner.
Read More »
Precision Fabricating with Over 40 Years of Experience
Quality Sheet Metal specializes in delivering precision, value, and customer service. With a client base that spans many diverse industries and a reputation for excellence that goes back over four decades, our clients know that we can provide the optimal combination of value and flexibility regardless of the challenge. See our video to learn what we can do for you. Through investments in state-of-the-art design, manufacturing, and quality control systems, Quality Sheet Metal remains focused on maintaining a high standard of quality, customer service, and competitive pricing. With an emphasis on customer satisfaction, Quality Sheet Metal is dedicated to establishing long-term partnerships, similar to the ones they currently have with their valued clients. If you're looking for a new partner with extensive capabilities in sheet metal fabricating and finishing, look no further.
Read More »
