Pneumatic Proportional Valve controls speed and velocity.

Pneumatic Proportional Valve controls speed and velocity.

Featuring microprocessor-driven position control, Model VP60 utilizes glandless spool and sleeve design and delivers more than 250 million operations at full stroke. Zero point adjustment via mini keypad provides application specific method of adjustment for leakage, drift, and offset, while multicolor LED indicates device status. Available with ratings up to 174 psi, Model VP60 features IP65...

Read More »

Reducing Valve is suitable for air systems.

Direct-acting, stainless steel Model DR20 provides air pressure reduction and shut-off, and can be utilized in gas applications including CO2 and N2. Class 4 seat leakage rating ensures tight shut-off, while 30:1 turndown ratio provides close pressure control with 2-stage reduction. Stainless steel bellows-sealed design prevents fugitive emissions. Sizes include Â-½, Â-¾, and 1 in. NPT.

Read More »
Air Switches increase safety in industrial applications.

Air Switches increase safety in industrial applications.

MV Series 3-way air switches, designed for use in place of electrical limit switches, eliminate spark hazard in industrial applications. Installed as NO, NC, or diverters, 1/8 in. ported air pilot valves eliminate need for wire shielding, transformers, and solenoids, simplifying control circuitry. Model MV-60 provides AND logic function with hookup that causes valve to respond only to...

Read More »
Multi-Port Ball Valve simplifies piping connections.

Multi-Port Ball Valve simplifies piping connections.

Plastic, lateral, 3-way ball valves replace conventional valve/tee connection combinations as well as zero dead-leg valves in piping system layouts. Available in sizes from Â-½-6 in., products can be made of PVC or CPVC with choice of FPM or EPDM seals. Integral ball permits flow to be diverted from center port to left or right ports without shutoff position. Valves feature one-piece molded...

Read More »
Dispense Valve applies cyanoacrylate adhesives.

Dispense Valve applies cyanoacrylate adhesives.

Pneumatically-operated 752 Series applies consistent amounts of adhesives and other assembly fluids on automated production lines. Fast, clean cutoff after each shot eliminates dripping, waste, and cosmetic damage to parts. Amount of cyanoacrylate dispensed is determined by fluid pressure, flow rate, and valve open time. Adjustable stroke control allows flow rate to be fine-tuned, while valve...

Read More »
Proportional Valves have integrated digital electronics.

Proportional Valves have integrated digital electronics.

Available in directional and pressure control configurations, proportional valves offer optional on-board digital electronics that incorporate pre-set digital amplifier and CAN-Bus interface. Software lets users pre-set hydraulic parameters and includes computer assisted maintenance and diagnostic program. Products come in NFPA D03 (NG6) and NFPA D07 (NG25) configurations with flows to 80 gpm and...

Read More »

Tank-Mounted Valve facilitates waste fluid handling.

Tank Sentry 340078 air valve prevents oil overflow in tanks. Separate from waste fluid tank, valve is incorporated into unit above tank. As waste fluid reaches top of tank, valve shuts off air supply to waste oil pump. Design provides safety and minimizes chance of oil spills. Air-operated portable drains and dispensers, drain accessories, and pumps are available to accompany Tank Sentry.

Read More »

Shut-Off Valve prevents damage to fluid handling pumps.

Low-level shut-off valve stops pneumatic fluid handling pump when material in bucket or other container reaches pre-determined level. This prevents damage to pump assemblies where no fluid is traveling through lines. Product mounts to drum cover inside fluid container and has lever connected by chain to flexible follower plate inside container. Valve is suited for chemical, heavy industrial,...

Read More »
Spray Valve features stainless steel wetted parts.

Spray Valve features stainless steel wetted parts.

Model SV1000SS provides finely controlled spray for low-medium viscosity fluids and coatings. Transfer efficiency is maintained by dual air-control system provided by spray valve controller. Piston-activated needle opens material inlet under low pressure, and secondary pressure source forces air around nozzle to produce spray. At end of operation, needle closes but secondary air remains on...

Read More »
Ball Valves come in 1/2 and 3/4 in. sizes.

Ball Valves come in 1/2 and 3/4 in. sizes.

In-line, 2- and 3-Way Divert, Fluid Flow Ball Valves feature mica-filled TeflonÂ-® seals, tri-clamp connections, and full-port design. Made of corrosion-resistant T-316 stainless steel, 2-piece design allows for breakdown by hand without use of tools. ID/OD polish is standard, and valves can be used in CIP systems. Comprised of 13 parts, valves are available with actuators, switches, and...

Read More »
Fresh Air Intake Designed to Meet ASHRAE 62.2 standards
Sponsored

Fresh Air Intake Designed to Meet ASHRAE 62.2 standards

Alan Manufacturing has a long history of developing innovative solutions for HVAC applications. With over 1,000 product designs under our belt, we have gained a reputation as the go-to source for HVAC dampers, hardware, duct supports, zone control systems, and much more. Adding to this extensive list of achievements we now announce the release of our new line of Fresh Air Intake products. Designed to meet ASHRAE 62.2 standards, they are the most robust and high-performance product of their kind. See our video to learn more.

Read More »

All Topics