Stepper Motors

NEMA34 Stepper Motors come in 95-156 mm long packages.
Stepper Motors

NEMA34 Stepper Motors come in 95-156 mm long packages.

Featuring RS485 and CANopen serial interface as well as programmable motion controller, MIS340/1/2 motors contains everything needed to solve control task as stand-alone unit or controlled via PLC/PC. Resolution of 819,200 step/revolution promotes smooth and silent running, and 8 I/O points can be configured to be digital input/output or analog input. Velocity and acceleration ratings are 0.01...

Read More »
8 mm Family of DC Motors, Gearheads, Encoders
Stepper Motors

8 mm Family of DC Motors, Gearheads, Encoders

With an outer diameter of only 8 mm, this new family of mini-drives provides maxi power. It is an impressive solution with a wide variety of combination possibilities using DC-Micromotors, with precision gearheads and micro-encoders. DC-Micromotors 0816 ... S The DC-Micromotors series 0816 ... S, available in 3, 6 and 8 Volt versions, have an exceptional power-to-volume ratio. The patented...

Read More »
Compact Stepping Motor has 20 mm frame size.
Stepper Motors

Compact Stepping Motor has 20 mm frame size.

Available with single or double shaft, PK 20mm is 1.8Â-º per step stepping motor with 20 mm (0.79 in.) frame size and 50 g (1.77 oz) mass. These characteristics suit limited-space applications, along with stack length of 30 mm and respective unipolar and bipolar torque ratings of 1.98 oz-in. (5 motor leads) and 2.8 oz-in. (4 motor leads).

Read More »
Hybrid Stepper Motors offer fine positioning capability.
Stepper Motors

Hybrid Stepper Motors offer fine positioning capability.

Incorporating neodymium magnets, precision-honed stators, and ground rotors, MAE® HN Series provides accurate open-loop control suitable for positioning applications. Standard Size 34 models are available in 3 versions with lengths from 2.64-4.92 in. and step resolutions of 200 steps/rev in full step mode. Holding torques from 397-1,076 oz-in. can be achieved, depending on model. Available...

Read More »
NEMA AC Motors come in 42, 48, and 56 frame sizes.
Stepper Motors

NEMA AC Motors come in 42, 48, and 56 frame sizes.

Available in 3-phase and single-phase TEFC and open drip-proof types, NEMA48 and NEMA56 motors are designed with 1.00, 1.15, or 1.25 service factors, depending on rating and frame size, for overload conditions. Units have double shielded bearings and are offered with rolled steel, cast iron, or aluminum housings. With input voltage of 115-120 Vac, NEMA42 motors deliver output power from 118-360 W...

Read More »
Stepper Motors

General Purpose Motors are NEMA Premium Efficiency certified.

Available from 1-250 hp, epoxy coated Elektrimax® Premium Efficiency general purpose motors resist rust and chipping, which prevents corrosion and wear. Units are IP55 sealing protected against water and dust. Vacuum pressure impregnation (VPI) helps keep electrical components cool and protected. VPI improves heat dissipation and protects against wire to wire vibration damage during...

Read More »
Stepper Motors

Stepper Motor Module accepts stepper motors up to 50 Vdc/5 A.

Using EP7041 EtherCAT® Motion Box, small EtherCAT motion applications can be implemented directly in field without protective control cabinet. Unit enables 64-fold micro-stepping, which ensures smooth and precise motor rotation. Measuring 5 x 1.2 x 1 in., IP67-rated box operates in harsh environments and contains encoder connection, 2 digital inputs for limit switches, and digital output...

Read More »
High Torque Stepping Motors have high efficiency design.
Stepper Motors

High Torque Stepping Motors have high efficiency design.

PKE series 2-phase motors have 1.65 in. square frame size and come in 3 stack lengths of 1.3 (PKE243x), 1.54 (PKE244x), and 1.85 (PKE245x) in. Output torque ranges from 34 oz-in. for PKE243A-L unipolar model up to 77.8 oz-in. for PKE245DA-L bipolar model. Offered with standard or double shafts, motors achieve shaft speeds of more than 2,000 rpm with 24 Vdc driver. Low heat generation enables...

Read More »
Stepper Motors

Nippon Pulse to Showcase Products at ATX South

Motion Control Specialist in Booth 2122, Will Showcase Linear and Stepper Motors RADFORD, VA -- For the first time, Nippon Pulse, a leader in the motion control industry, will be exhibiting its products at ATX South, the top automation showcase tradeshow in the South/Southeast Region. This year's show will be held at the Charlotte Convention Center from April 28-29, 2010. In its inaugural...

Read More »
NEMA 34 Steppers
Stepper Motors

NEMA 34 Steppers

Santa Clara, CA - Lin Engineering is pleased to announce that the 8718 NEMA 34 step motor series has been recognized with a certification of compliance to Underwriters Laboratories Inc.'s (UL) standards. The 8718 product line is a series of high torque, 2 phase stepper motors. The motors are available in three body lengths: 2.6 , 3.8", and 5.0" and are capable of up to 1,288 oz-in of holding...

Read More »
Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine
Sponsored

Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine

CS Unitec is a leader in power tools designed for industrial applications, with products that set the standard for robust performance and industry-leading reliability. Adding to our long list of innovation is a new line of pipe cutting machines. For cutting and beveling pipe up to 2" in thickness and diameters from 12" to 63", no other cutting system comes close. See our video to learn more.

Read More »

All Topics