Fork Sensor detects all label types.
GSU 14/24 ultrasonic sensor has either PNP or NPN outputs, and makes adjustments via push button remote teach-in feature. It comes standard with anodized aluminum housing and IP 67 protection rating making it suitable for almost any environment. Sensor can detect foil on foil, foil on paper, paper on paper, metallized foil, and thin metal foils as well as clear, metallic, and conductive ink...
Read More »Position Control Sensors feature ASCII serial protocol.
TemposonicsÃ-® S Series ServoSensors combine sensor and embedded closed-loop position controller. ASCII protocol and Windows(TM) application setup software enable use of common translator software. Model SH rod style sensors are designed for internal mounting where high pressure conditions exist (5,000 psi continuous/10,000 psi spike). Model SP profile sensors are magnet-mounted and are used...
Read More »Sensor offers continuous level measurement.
+GF+ SIGNET 2222 Magnetostrictive Level Sensor measures non-coating liquids such as water, acids, bases and corrosive chemicals. It is available with 316SS or SYGEFÃ-® PVDF body. NEMA 6/IP68 rated tube is 5/8 in. and houses wiring and sensor electronics. Microprocessor-based technology provides accuracy of Ã-
Read More »Pressure Sensors feature digital CANopen-BUS output.
Melt and Industrial Pressure Sensors with digital CANopen-BUS technology converts low signal pressure sensing elements from analog to digital, then processes further in intelligent microprocessor. Scanning and conversion rate of pressure signal is 20 milliseconds. Digital pressure signal with 13 bit resolution is continuous on 2-wire CAN-BUS connection, and is controlled and analyzed by CANopen...
Read More »Understanding Lights Out Manufacturing
This white paper gives an overview of understanding lights out manufacturing.
Read More »Current Sensor is self-powered.
TCS Series Go/No Go Sensor/PLC interface can be directly connected to PLC's digital input module or to load rated up to 1 A. It can detect overcurrent or undercurrent events, and signal PLC or switch load device to ON or OFF. Onboard toroidal sensor monitors current flow through ac loads up to 50 A steady, 300 A inrush. TCS Sensor is available with adjustable or factory-fixed actuation point.
Read More »Torque Sensors are designed for low torque applications.
STS2220 rotary shaft torque sensors are available in capacities from 1.0 to 10.0 Nm. They feature one-piece outer housings and pre-lubricated bearings, and accept either AC or DC excitation voltage for compatibility to most readout instruments. Units have 1.5 mV/V nominal output at rated capacity, bridge resistance of 350 ohms, maximum speed of 10,000 rpm, and non-linearity of +/- 0.1% of full...
Read More »Rotary Torque Sensors eliminate need for slip ring.
Model 01279 line of rotary torque sensors use non-contact infrared digital signal transmission, eliminating maintenance and wear problems of conventional slip ring technology. Sensors have high level analog output to represent torque load. They can be used as drop in replacements for many existing rotary torque sensors.
Read More »Fixed Gas Sensor features 2 gas monitoring points.
WorksAlone 2(TM) fixed-point gas detection monitor, incorporating dual-sensor design, displays gas concentration levels and signals alarm conditions when programmed alarm points have been exceeded. It provides 1 or 2 gas monitoring points installed on-board or remotely from electronic controllers. Features include automatic, non-intrusive calibration and split-screen, extended-temperature LCD...
Read More »Sensor converts shaft to torque sensor in 15 minutes.
Model 1650B Snap-On Rotary Torque Sensor clamps onto drive train to take measurement data. It does not break into drive train to install in-line torque cell, and requires no professional installation. Model 1650B comes pre-calibrated. Installation requires users to clamp on 2 halves of sensor shell, position antenna, and connect wireless receiver. Available for shaft diameters from 2.5 to 15 in.,...
Read More »Tranducer Kit is fully re-rangeable.
DP15 Pressure Transducer Kit contains variable reluctance sensor with 10 replaceable sensing diaphragms, O-rings, bleed screws, gaskets, AC power adapter, CD379 portable indicator with LCD readout and cables. Diaphragms support full-scale ranges between Ã-
Read More »How SpinSelect Can Save You Time and Money
Thanks to the unique SpinSelect™ Multi-Pocket selectable quick change tool holder, it's time to rethink the range, complexity and volume of parts that your lathe can produce. Our Spin-Select™ tool was created to increase productivity and consistency by decreasing downtime associated with lathe cutting tool and insert setups or changeovers. This product is a game-changer for the industry and we're pleased to show you why.
Read More »