Lights

Power and Light System produces 50,000 lm.

For portable power and light, 2-Headed XT LENTRY® Polelight has two 650 W halogen lights on single telescoping pole, 1,600 W Honda EU2000i generator, and all-terrain retractable LENTRY legs. Each light head produces 25,000 lm, has its own on/off switch, pivots forward and backward, and rotates more than 400°. System stands about 9 ft tall with legs and polelight fully extended. With...

Read More »
Reversible Plate Compactors feature two exciter shafts.
Plate / Roller Compactors

Reversible Plate Compactors feature two exciter shafts.

Available inÂ- three models with 9.3 hp Honda gas-powered engine or Hatz diesel-powered engine, Reversible Plate Compactors deliver up to 11,241 lb of centrifugal force. Compactors feature travel speed up to 85 fpm, working width from 20–25 in., and 4,200–5,400 vpm. Capable of operating in tight spaces, machines are suitable for large foundations, retaining walls, and compaction of side...

Read More »
Mid-Size Rammers prepare jobsites for flat finish.
Rams

Mid-Size Rammers prepare jobsites for flat finish.

Employing GXR120 Honda engine, ATC130H and ATC170H are suited for use in confined spaces, deliver 650–700 blows per minute, and offer 2,800–3,500 lb of impact force. Design incorporates protection for engine, and 3-way throttle lever shuts down engine as well as fuel supply. Along with built-in tachometer and hour meter, rammers offer capacities of up to 3,800 ftÂ-²/hr compacted area and...

Read More »
Cold Milling Machines feature rear rotor design.
Milling Machines

Cold Milling Machines feature rear rotor design.

Designed to extend cutting tool life, BM-35 Series features BMS 15 interchangeable holder system, which utilizes single bolt for holder retention and requires low tightening torque of 75 lb-ft. Low front face position maximizes efficiency while allowing full tooth rotation. In addition, machines incorporate logical operating layout, intuitive controls, and low noise levels. Vibration isolated...

Read More »
Laser-Guided Screed meets or exceeds F-number requirements.
Screeds

Laser-Guided Screed meets or exceeds F-number requirements.

Utilizing 12 ft wide screeding head and 16.5 ft telescopic boom, LS175 LaserStriker screeds 192 ftÂ-² per pass. System incorporates 59 hp Kubota turbo-charged diesel engine and heavy-duty auger plow powered by hydraulic system, which helps in maintaining grade for smooth finish, even when screeding low-slump concrete. With 360° upper frame rotation, it is possible to screed from all...

Read More »
Mortar Mixers meet needs of masonry contractors.
Masonry Equipment

Mortar Mixers meet needs of masonry contractors.

Comprising models with 6 and 8 ftÂ-³ capacities, Mortar Mixers are powered by Honda engines and feature steel design for extended life expectancy. High-speed hubs feature grease axle bearing, and number of paddles optimizes mix quality. Suited for use by masonry contractors, mixers also feature rugged, hinged shroud that covers engine.

Read More »
Leak-Tight Connectors mate to shallow depth threads.
Connectors

Leak-Tight Connectors mate to shallow depth threads.

Providing safe manual or automated leak-tight connections to shallow depth female threads, FN Series is suited for vacuum testing, media filling or flushing, and performance testing. Modular units enable rapid change outs between squeeze lever, pneumatic thumb, and pneumatic pilot actuation methods to meet application. Constructed of stainless steel and anodized aluminum, connectors feature split...

Read More »
Mechanical-Drive Riding Trowel is ergonomically designed.
Power Trowels

Mechanical-Drive Riding Trowel is ergonomically designed.

Intended for large and small contractors, Mechanical Super Pro (MSP) 470 is powered by 44Â- hp, air-cooled Kubota diesel engine and offers hydraulic power steering with independent manual pitch controls. Raised operator platform and hydraulic joystick steering lend to ergonomics, and two 46 in. dia, 5-blade, non-overlapping rotors operate at speeds to 180 rpm. Other standard...

Read More »
DE-OX® Oxide Inhibiting Compound from ILSCO
Inhibitors

DE-OX® Oxide Inhibiting Compound from ILSCO

ILSCO Celebrates 120 years in 2014… ILSCO's De-Ox® oxide inhibitor is available in three distinct formulas.Â- The standard non-grit, petroleum based formula is suitable for aluminum and copper connections. It performs very well in keeping moisture and air from penetrating the connection, thus preventing oxidization and therefore prolonging the life and integrity of the connection....

Read More »
Riding Trowel offers rotor speeds up to 160 rpm.
Power Trowels

Riding Trowel offers rotor speeds up to 160 rpm.

Powered by 59 hp liquid-cooled Kubota diesel engine, Allen HDX610 features all-hydraulic drive and steering as well as hydraulic pitch controls. Two 46 in. diameter, 6-blade non-overlapping rotors provide 100 in. panning capacity. Additional features include electric-powered spray system for application of retardant, 6-gallon retardant tank capacity, engine warning cluster gauge, cup holder, arm...

Read More »
Precision Machined Parts for High Tech Applications
Sponsored

Precision Machined Parts for High Tech Applications

For precision and value that sets the standard for quality and craftsmanship, EGS Production Machining is the source for precision and value. Our extensive capabilities and dedication to customer service allow us to deliver the optimal manufacturing solution. See our video to learn more.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers