Lamination Adhesives improve holdout when aerated.
Adhesives

Lamination Adhesives improve holdout when aerated.

Aerobond 32-192A and 12-200A adhesives are able to contact substrate surface without flowing down and away from where bonding should occur. Type 32-192A is for Automatan and similar laminating equipment; 12-200A formulated dextrin adhesive is for general purpose laminating. Both should be applied with nip rollers.

Read More »
Adhesive Tapes minimize media fogging and head corrosion.
Adhesive Tapes

Adhesive Tapes minimize media fogging and head corrosion.

ARclean(TM) 9006 and ARclean(TM) 9019 are low-outgassing products for use in fabrication of tape seals and labels in hard disk drive assemblies. ARclean(TM) 9006 cleanly strippable adhesive features 3 mil matte chrome polyester backing. ARclean(TM) 9019 electronically clean adhesive features 2 mil thermally printable, white polyester film label stock. Both adhesives have ultra low total VOCs and...

Read More »
Ceramic Adhesive is formulated with phosphate binder.
Adhesives

Ceramic Adhesive is formulated with phosphate binder.

Ceramabond(TM) 690 single part, boron nitride filled ceramic adhesive bonds and coats in temperatures to 2700°F, and can be used in oxidizing atmospheres to 1560°F and reducing and vacuum environments to 2700°F. Thermal conductivity is 55 W/m-°K, and dielectric strength is rated at 500 volts/mil. Exceptional resistance is shown to molten glasses and metals. Curing time is...

Read More »
Epoxies

Thermally Conductive Epoxy cures at room temperature.

Two component EMCAST has viscosity of 130,000 cps, specific gravity of 1.90, and glass transition temperature of 125Â-ºC. Its thermal conductivity is 3 W/mK, and it is not electrically conductive. 100% solids epoxy has no solvent for zero VOCs. Epoxy cures in 8 hours @ 25°C, 1 hour @ 65°C, and 15 minutes @ 100°C. It is available as pre-mixed and frozen syringes or in two...

Read More »
Epoxy Adhesive has low vapor pressure.
Epoxies

Epoxy Adhesive has low vapor pressure.

Two-part Tra-Bond 2116 thixotropic adhesive can be used in electronic and industrial applications where high-fill, non-sag adhesive is needed. It bonds well to many substrates including metals, glass, ceramics, wood, and plastics. Adhesive cures at room temperature, is electrical insulator, and is NASA outgassing approved. It resists chemicals and weather.

Read More »
Adhesives

Graphite Adhesive works at temperatures to 5400° F.

Resbond 931 cures at 250°F to form 99% pure graphite bonds that have bond strengths in excess of 2500 psi. Bonds are electrically conductive and resist reducing atmospheres, most chemicals, and solvents. Applications include repairing cracked or broken graphite trays, fixtures, and dies; filling and rebuilding crevices, cracks, and worn areas; and bonding graphite cloths, felts, and boards....

Read More »
Machinery Adhesives lock and seal nuts and bolts.
Adhesives

Machinery Adhesives lock and seal nuts and bolts.

Superlock adhesives provide positive locking and sealing on both active and inactive surfaces. Screw Lock Grade 2222 low-strength threadlocker is for spiral screws less than 1/4 in. diameter. Medium-strength Grade 2242 works on nuts, bolts, and screws with diameters up to 3/4 in. Grade 2262 high-strength formula controls torque/tension and clamp load on larger bolts and nuts in applications...

Read More »
Lens Bonding Adhesives are optically clear.
Adhesives

Lens Bonding Adhesives are optically clear.

Lens assembly adhesives for precision bonding, mounting, laminating, and fixturing applications have good adhesion to lens construction materials and to most metal, coated or painted frames and holders. Applications include cameras, microscopes, as well as eyeglass and sunglass lenses. Special UV blocking grades are available that adhere to PVA, CR-39, and CAP. These flexible lens bonders provide...

Read More »
UV Adhesive bonds fiber optics.
Adhesives

UV Adhesive bonds fiber optics.

TRA-BOND F 175 clear, low viscosity adhesive bonds metals, ceramics, and most rigid polymers. Cure time of a few seconds upon exposure to ultraviolet light makes it suitable for fiber optic terminations where fast cure is required. It produces very little shrinkage upon cure, so stress is minimal. Adhesive also works well in high humidity environments or in applications that require thermal...

Read More »
Moisture Resistant Encapsulant has smooth consistency.
Encapsulants

Moisture Resistant Encapsulant has smooth consistency.

Tra-Bond 933-1.5 electrically insulating epoxy encapsulant is formulated to provide smooth crowns over devices of wire bonds. Encapsulant provides protection from thermal and mechanical shock. Compound is stable at room temperature for up to three months, but is best kept stored at -40°C or colder, since filler may settle.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers