Structural Adhesive binds hard-to-bond plastics.
Adhesives

Structural Adhesive binds hard-to-bond plastics.

Suited for rapid production and repair applications, ReAct(TM) 784 allows controlled assembly timing for bonding substrates such as steel, aluminum, phenolic, PVC, ABS, polycarbonate, and glass. This 2-component, no-mix system produces shear strengths from 400 to 4,800+ psi and exhibits resistance to moisture, chemicals, and temperatures to 275°F. Once EF(TM) Activator 15 is applied to one...

Read More »
Foam Tape is used in mounting, fastening, and sealing.
Adhesive Tapes

Foam Tape is used in mounting, fastening, and sealing.

Double-coated, polyethylene P-3200/P-3300 resists temperatures up to 200°F and provides instant adhesive to mount and fasten lightweight parts. Low-density, closed-cell PF1400 is coated on one side with pressure-sensitive adhesive, protected by release liner. Long-term sealing and abrasion-resistance make tape suited for insulation, sound dampening, and cushioning. Crosslinked, polyethylene...

Read More »
Double Coated Adhesive Film is suited for temporary bonding.
Adhesive Tapes

Double Coated Adhesive Film is suited for temporary bonding.

Formulated with permanent acrylic adhesive on one side and removable acrylic adhesive on other, Dublfilm S1039 bonds to high surface energy materials such as glass and metal and removes without leaving residue. Dimensionally stable, polyester film is supplied with 74 lb lay flat release liner to facilitate application and die-cutting. This double-coated adhesive tape will permanently laminate to...

Read More »
Adhesives

Deep-freeze Adhesive offers instant adhesion in cold.

Suitable for base papers without barrier primer, Collano® L3 706 deep-freeze adhesive provides quick-stick performance on cooled surfaces even with little initial pressure. Deep-freeze label sticks to packaging films and cardboard, features labeling temperature down to -20°C and service temperature as low as -40°C, and is approved for indirect food contact.

Read More »
Epoxy Adhesive meets NASA low outgassing specifications.
Epoxies

Epoxy Adhesive meets NASA low outgassing specifications.

Formulated to setup in 3-5 min in 10-20 g masses at room temperature, EP65HT-1 ultra-fast curing, high temperature resistant epoxy adhesive bonds with metals, glass, ceramics, woods, vulcanized rubbers, and plastics. It has Shore D hardness of >75 and volume resistivity of >1014 ohm-cm. Mixed viscosity is 60-70,000 cps and mix ratio is 10 to 1 by weight. Available in pint, quart, gal, and 5 gal...

Read More »
Resins

GE's Flame Retardant (FR) Flexible Noryl Resins Now Recognized Under UL1581 as an Acceptable Wire Coating Material Candidate for 80 C, 90 C & 105 C Applications

GE's Resins Offer Top Performance for Appliance Wire Coatings with Added Benefits of Non-Halogenated FR, Thin-Wall Constructions, and Environmental Responsibility PITTSFIELD, MASS. - May 2, 2006 -GE Plastics has announced that various grades of its flame-retardant Flexible Noryl* resin for wire coating and insulation have been listed by Underwriters Laboratories (UL) under the UL1581 reference...

Read More »
Molding Compound is used in hearing aids.
Adhesives

Molding Compound is used in hearing aids.

Designed for vent channel formation and shell repair, ResinAid 3691(TM) pink one-part acrylic adhesive cures tack-free in less than 20 sec on exposure to UV or visible light of right intensity. In less than 10 sec, this high viscosity product cures to thickness of 0.060 in., making it a suitable alternative to traditional vent formation materials. Using 6 step process, 3691(TM) ResinAid will...

Read More »
Cement

Stone Mortar suits veneer and tuck-pointing applications.

Contractor grade blend of Portland cement, hydrated lime, masonry sand, and other ingredients, QUIKRETE® Veneer Stone Mortar is available in standard gray or colored for use in mortar joint applications. Mortar formulation complies with ASTM 270 and ASTM C 387 requirements and is suitable as bonding coat to adhere stone to wall or as scratch coating applied over expanded metal lath....

Read More »
Insulation

Thermoset Composite electrically insulates transformers.

Used to separate and isolate electrical contacts, oil-resistant NP613 maintains mechanical strength when used in oil-filled transformer equipment. It also maintains dimensional stability at elevated operating temperatures, guaranteeing contact will be separated and engaged as needed. Constructed from electrical grade of kraft paper and modified resin, NP613 has flexural strength of 27,000 psi,...

Read More »
Epoxies

Adhesive and Epoxy are designed for flip chip assembly.

Material GPC-251A/B is silver-filled, electrically conductive, 2-part, room-temperature curing adhesive used to connect bumps on underside of circuit boards. Product cures in 24 hr @ 25°C, 60 min @ 65°C, and 5 min @ 120°C. Material 123-38A/B-187 is thermally conductive underfill epoxy that strengthens chip package, protecting it from moisture and adding mechanical strength....

Read More »

All Topics