New Iris 3D with Vision Positioning System Delivers Laser Line Visibility, Even in Bright Ambient Lighting Environments and on Difficult Work Surfaces

New Iris 3D with Vision Positioning System Delivers Laser Line Visibility, Even in Bright Ambient Lighting Environments and on Difficult Work Surfaces

Iris™ 3D is portable system and enables aerospace manufacturers to streamline composite ply layup, paint masking and a host of other labor-intensive tasks. Enables operators to easily locate laser lines and get the job done faster. Positioning mount is innovative remote-controlled option that optimizes the system's projection by repositioning the laser on challenging tools or large work areas.

Read More »
New FRM Series Roof Mounts Eliminate the Need for Lift/Bucket Service Calls

New FRM Series Roof Mounts Eliminate the Need for Lift/Bucket Service Calls

The FRM Series Non-Penetrating Roof Mounts are suitable for wireless security surveillance systems, off-air antenna and satellite internet systems. The units are available in FRM-125, FRM-166 and FRM-200 models with 35 x 35 x 60.5 in., 35 x 35 x 30.5 in., 35 x 35 in x 30.5 in. dimensions respectively. The mounts utilize 8 x 8 x 16 in. cinderblocks as ballast and are constructed of steel and uses...

Read More »

Winsted Corporation Releases New Sky Track Monitor Walls to Mount Monitors on Walls Where Mounting is Not an Option

The Sky Track Monitor Wall features monitor mounts, a removable panel, a leveling foot for height adjustments, a customizable steel angle, two mounting contact points and the ability to control monitor viewing distances. The product is measured at 1.5 inches by 3 inches for horizontal extrusion for structural support and 1.5 inches by 1.5 inches for vertical extrusions to mount monitors.

Read More »
New Lifeline Boost Access Control Pedestal Mount Comes with Enclosed Raceway

New Lifeline Boost Access Control Pedestal Mount Comes with Enclosed Raceway

The Lifeline Boost Access Control Pedestal Mount is offered in standard premium, card collector and Nortech card collector models. The standard premium model is used for integration of card reader, barcode reader or biometric devices. The card collector model is designed for integrating a third-party card collector device whereas the Nortech model comes with Nortech MRC350 card collector. The...

Read More »
New Three-Axis Gimbal Mount Features Full 360 Degrees Rotation of Each Axis

New Three-Axis Gimbal Mount Features Full 360 Degrees Rotation of Each Axis

Optimal Engineering Systems, Inc. announces AU300-AER three-axis Gimbal Mount with 10kg load handling capacity and 300 mm x 300 mm clearance around the roll axis stage. The bi-directional stepper motors with knobs for manual adjustments derives azimuth, elevation and roll axis. Each axis has a low backlash worm gear drives, precision V groove, cross roller bearings, repeatability and positional...

Read More »
HellermannTyton Introduces FlexTack That Can Work With 18 to 50 Pound Cable Ties to Provide Stability

HellermannTyton Introduces FlexTack That Can Work With 18 to 50 Pound Cable Ties to Provide Stability

HellermannTyton’s FlexTack cable tie mount adheres to curved and moderately angled surfaces where only a screw mount would do the job. It enables installers to install route wires, cables and hoses in off-limit areas. The product is engineered to be used on varnished, powder coated, bare metal or plastic surfaces. The tie mount is manufactured from heat stabilized PA66 nylon in black and white.

Read More »
New Magnetic Mounts Offer Clean and Reliable Connectivity for Automation

New Magnetic Mounts Offer Clean and Reliable Connectivity for Automation

Balluff's new magnetic mounts provide a simple and cost-effective solution for regular tool or die changes. The mounts use strong earth magnets to easily engage or disengage. The magnetic mounts are designed for Q40- and M30-style inductive couplers and also protect them from impact or abrasion. Their break-away capability makes the tool or die changing quick and simple, reducing downtime.

Read More »
Piab's New Suction Cup Mount is Designed for Industry Standard End-of-Arm Tooling Connections

Piab's New Suction Cup Mount is Designed for Industry Standard End-of-Arm Tooling Connections

Piab’s Suction Cup Mount comes with interchangeable parts for mix and match mounting system. Unit provides mounting options such as Universal joint, mount (2 x 8/10.5mm), Lock-pin (19mm), and Ball-joint. Offered in lengths from 45 to 200 mm, mount is designed for handling, for instance, automotive body parts or plastic details. Unit’s ball-shaped fastener comes with an optional mechanism and...

Read More »

All Topics