Transimpedance Amplifier permits digital entry of A/W.
Model PdA-750 provides direct digital readout of current generated from photodiode, photomultiplier, or similar current source. Full-scale input ranges are Ã-
Read More »
CMOS Op Amps drive 16-bit data converters.
Models OPA725 and OPA726 are 12 V, high-speed operational amplifiers that achieve 20 MHz bandwidth, 30 V/Ã-µs slew rate, and 0.0003% harmonic distortion with 16-bit settling time. Input common-mode range extends to ground for true single-supply operation, and output swings to within 150 mV of rails, maximizing dynamic range. Both are specified for operation from -40 to +125Ã-
Read More »
Differential Amplifier is optimized for video applications.
Model LT6552 3.3 V wideband difference amplifier minimizes effects of high-frequency noise pickup, allowing signals to be sent over long lines without corruption by external sources. Common mode rejection is >60 dB at 10 MHz. Unit comes in 3 x 3 mm DFN package and features 75 MHz -3 dB bandwidth, 600 V/Ã-µs slew rate, and Ã-
Read More »
Rail-to-Rail Op Amp features 3-12 V operation.
Current feedback amplifier, Model LT6210 offers adjustable supply current that is programmable from 300 Ã-µA to 6 mA with corresponding bandwidth from 10-200 MHz. By changing one resistor, each LT6210 can be configured to attain specific bandwidth and slew rate for given supply current. Unit is offered in 6-lead ThinSOT(TM) package and can be used as video line driver pre-amp, buffer, or...
Read More »
An Introduction to Purchasing Castings
To learn how Liberty Cast Products can guide you through your sand casting project, download now.
Read More »
Mono Amplifiers drive 16-32 ohm speakers and earpieces.
Models TS419 and TS421 operate from supply of 2 V and draw max of 2.5 mA. Standby current consumption can be as little as 10 nA. Amplifiers are available with external gain configuration or with fixed gain of 6, 12, or 18 dB. Signal to noise ratio is typically 98 dB with 5 V supply. Offered in MiniSO-8 and DFN8 packages, amplifiers include On/Off click reduction circuitry and are suited for...
Read More »
Audio Amplifier suits portable, wireless applications.
Model TPA6211A1 Mono Class-AB Amplifier offers over 340 mW of power per mmÃ-² and can deliver 3.1 W of power into 3 ohm load at 10% total harmonic distortion. Device comes in 3 x 3 mm QFN package and 3 x 5 mm MSOP package. Typical applications include cell phones, smart phones, and PDAs.
Read More »
Sources and Amplifiers suit laboratory applications.
Leveraging diode-pumped erbium doped fiber technology, Broadband ASE (amplified spontaneous emission) sources and EDFAs (erbium doped fiber amplifiers) are packaged for test and measurement of photonics components in 1550 nm spectral region. Self-contained BBS-410 and BBS-430 sources generate broadband output as high as 25 mW. Fully-integrated FPA-410 and FPA-415 EDFAs feature signal gains of...
Read More »
Rail-to-Rail Operational Amplifiers draw less than 1 mA.
Models LT6220 single, LT6221 dual, and LT6222 quad rail-to-rail input and output precision op amps are rated at 60 MHz and can operate from supplies of 2.3-12.6 V. Characteristics include 350 Ã-µV max input offset voltage, 150 nA max input bias current, 82 dB CMRR, and 90 dB voltage gain. Devices have output current capability of 50mA for driving heavy loads. They are rated for 0 to 70Ã-
Read More »
Op Amp features 100 MHz gain bandwidth.
Model LT6206 dual video, operational amplifier operates on supplies from 2.7-12.6 V with 400 V/Ã-µs slew rate and high output drive of 50 mA. Rail-to-rail outputs swing within 60 mV of either supply rail, making unit suited for 3 V operation requiring max output dynamic range. Amplifier offers over 90 dB of channel isolation at 10 MHz. Video specifications include 0.05% differential gain,...
Read More »
Operational Amplifiers suit high speed, low-voltage designs.
Single, dual, and quad rail-to-rail input and output models (LT1803, LT1804, and LT1805, respectively) offer 85 MHz gain-bandwidth product and 100 V/Ã-µs slew rate. Voltage feedback op amps draw 3 mA supply current and offer minimum open loop gain of 86 dB and CMRR of over 78 dB. Products operate from supplies from 2.3-12.6 V. Model LT1803 is offered in 5-pin SOT23 and 8-pin SOIC packages,...
Read More »
Oilfield Improvements® Wheeled Rod Guide® Couplings Celebrate 35th Anniversary
For over 35 years our Wheeled Rod Guide Couplings, have been at work in oil fields across the globe. Our products are engineered to extend the service life of sucker rods and tubing, delivering cutting-edge innovation that enhances oilfield operation, maximizes output, and enhancing overall operations. To learn about the advantages of using Wheeled Rod Guide Couplings in your wells, see our video.
Read More »
