New High-power Amplifier Operates Across Broad Frequency Range of 300 MHz to 6 GHz
Model TA1264 weighs 16 ounces, measures under 4” square and under 1” in height. Enclosed in a rugged enclosure and designed for operation in harsh environmental conditions. Provides advanced built-in PA monitoring and control sections that are directed by microprocessor, FPGA, CPLD or a combination of these devices.
Read More »
New Liquid Cooled SSPA Comes with 2U Amplifier Drawer and Full System Rack
Features solid state design. Offers digital peak and RMS detection. Consists of system controller in 3U and up to 16 hot swappable 2U amplifier drawers.
Read More »
New Low-noise Amplifier with Frequency Range of 18 to 42 GHz
ERZ-LNA-1800-4200-24-6 provides a gain of 24 dB with a noise figure of 5 dB. Available with output power P1dB of +9 dBm and gain flatness of +/- 1.5 dB. Ideal for industrial, SATCOM, aerospace and military applications.
Read More »New F1490 RF Amplifier Features Ultra-low Quiescent Current of 75 mA
Delivers high gain with selectable modes and ultra-low power consumption. Covers key sub-6 GHz 5G frequency bands from 1.8 GHz to 5.0 GHz. Operating temperature ranges up to +115°C TCB.
Read More »
A Quick Guide to MASKING SOLUTIONS
This guide will provide an overview of the different masking options, and provide insight on which to use for your product.
Read More »
New Wideband High-Power Amplifier Provides 49 dB of Gain
Operates from 32-38 GHz (Ka-band) and is designed to offer consistent output power across the entire band of operation. Supports rapid development of microwave systems for EW, avionic and ground radar, SATCOM, 5G, and test equipment operating around Ka-band frequencies. Meets MIL-STD-810F standards against temperature, shock, vibration and acceleration.
Read More »
New Model 2225 Amplifier Provides Asymmetrical and Random Pulse Width and Duty Cycle Operation
Features liquid cooled and scalable architecture that operates from 5.2 to 5.9GHz. Offers system controller in 3U and up to 16 hot swappable 2U amplifier drawers with each amplifier drawer containing an integrated power supply in its 2U chassis. Eliminates the risk of an RF section or single power supply failure taking the entire amplifier offline.
Read More »
New Solid-state High-power Amplifiers with Operating Voltage of 48 V
1219 delivers 25 W minimum output power and related RF performance under all specified temperature and environmental conditions. Designed for RF product testing, broadband mobile jamming and band-specific high-power applications in the UHF, L, S and C frequency bands. Available with 7.0 x 4.0 x 1.1 inches diemsions and suitable for CW, AM, FM and pulse.
Read More »
New DC Linear Brush-type Servo Amplifiers for Low Noise Operation
LCAM 5/15 allows the current to flow continuously to the motor which prevents any dead-band issues that occur in many PWM type amplifiers. Available with wide power supply range of +24 to +70 volts DC. Ideally suited to drive complete line of voice coil linear actuators.
Read More »
New Wideband High-Power Amplifiers Can Withstand in Harsh Environments
Offer broadband frequency coverage and consistent output power throughout bands as high as E-band. Feature bandwidth/output power combinations from 1-23 GHz/27 dBm to 75-83 GHz/27 dBm. Ideal for critical wider band applications.
Read More »
New GaN Solid-State Power Amplifiers are Ideal for Satellite Communication Uplink Applications
Bobcat BUCs enable users to shrink footprint while increasing the speed of their satellite communications uplink. Puma SSPAs/BUCs offer internal L-Band BUCs, internal LO reference, web-based GUI and ethernet SNMP (v1 or v3). Falcon SSPAs/BUCs available in Ku and Ka-Bands that includes multi-band switchable BUCs built into the Ka-Band units.
Read More »
What Can Test Devices Spin for You?
Test Devices helps you ensure the safety and efficiency of your high performance machines with cutting edge spin testing, rotor engineering, and precision balancing capabilities. Check out the video to learn more.
Read More »
