Electronic Amplifiers

Strain Gage Amplifiers handle multiple channels.
Electronic Amplifiers

Strain Gage Amplifiers handle multiple channels.

MAC MultiAmplifier Card and IMUX Tension Multiplexer provide multi-point tension monitoring. MAC amplifies signals from up to 8 tension transducers or load cells, and supplies corresponding number of 0 to 10 Vdc signals. Signals may be used as inputs to drives, PLCs, or other control devices. Additional 0 to 1 mA or 0 to l00 microA signal is supplied as meter output. IMUX can select and display...

Read More »
Optical Amplifier offsets signal loss from DWDM.
Electronic Amplifiers

Optical Amplifier offsets signal loss from DWDM.

Scorpion Amplet MMP-HP7020 high-gain, low-noise amplifier module has 16 dB of total output power and provides up to 20 dB of gain across C-Band, while generating less than 5.5 dB of noise. Suitable for in-line metro and access applications, it offsets signal loss created by DWDM and optical conditioning devices. It has MSA-compliant footprint of 90 x 70 x 12 mm, and complies with Telcordia...

Read More »
Load Cell includes amplifier/conditioner.
Electronic Amplifiers

Load Cell includes amplifier/conditioner.

MLC Series (Mini Load Column) Compression Only Load Cell, constructed from stainless steel, is offered in range from 2,000 to 30,000 lbs. It mounts in shallow, machined flat pocket or smooth, flat surface, either free or fastened via bottom, tapped hole. Model TM0-1, 12 Vdc powered Amplifier/Conditioner Module, provides dedicated conditioning and several units can be powered from common power...

Read More »
Amplifier conditions strain gages and load cell sensors.
Electronic Amplifiers

Amplifier conditions strain gages and load cell sensors.

MCR-Strain Gage amplifier module includes 1,000 V 3-way galvanic isolation between power supply, input, and output circuits. It supports strain gages/load cells with resistances from 120 to 20,000 ohms. Module filters and conditions signals to eliminate unwanted signal noise with DIP switch selectable cutoff frequencies of 30 Hz or 5,000 Hz. Outputs are provided for voltage (0-10, -±10, 0-5, or...

Read More »
Signal Conditioner controls multiple units.
Electronic Amplifiers

Signal Conditioner controls multiple units.

Rack-mountable Model 2775B fits 1 to 6 units in 19 in. enclosure. It allows centralized control of up to 20 units per COMM port via RS-232 computer interface. Offerings include dynamic range from 0.01 to 100,000 engineering units and sensor input sensitivity range of 0.0001 to 10,000 mV/EU or pC/EU. It provides 3 outputs: AC output voltage proportional to input, DC output voltage proportional to...

Read More »
Op Amps achieve 410 MHz, 2200 V/us while consuming 2.5 mA.
Electronic Amplifiers

Op Amps achieve 410 MHz, 2200 V/us while consuming 2.5 mA.

Teeny(TM) MIC923 achieves 2200 V/us slew-rate with 410 MHz gain-bandwidth product (GBW), and MIC922 achieves GBW of 230 MHz and slew-rate of 1500 V/us. Intended for signal buffering, MIC922 is unity-gain stable, and MIC923 is optimized for applications with gain of 2 or greater. Both are capable of driving unlimited capacitance. Manufactured in SC-70 packaging, op amps are specified for supply...

Read More »
Op Amps in tiny SOT23-8 package draw low current.
Electronic Amplifiers

Op Amps in tiny SOT23-8 package draw low current.

MIC862 dual op amp provides -3dB bandwidth of 5 MHz and gain-bandwidth product of 3 MHz, yet consumes only 31 microA current per channel. MIC863 dual op amp operates at 4.2 microA per channel, while still providing -3 dB bandwidth of 800 kHz and gain-bandwidth product of 450 kHz. Both are unity gain stable and specified at supply voltage of 2, 2.7, and 5 V. Input offset voltage is 0.1 mV...

Read More »
Broadband Amplifier meets aircraft testing standards.
Electronic Amplifiers

Broadband Amplifier meets aircraft testing standards.

Self-contained, air-cooled, solid state Model 75A400 75 W amplifier spans frequency range from 10 kHz to 400 MHz. This makes it suitable for laboratory applications, antenna and component testing, plus commercial aircraft conducted susceptibility testing per DO-160D. Push-pull MOSFET circuitry lowers distortion, improves stability, and allows operation into any load impedance without damage.

Read More »

All Topics