Precision Rail-to-Rail Op Amp draws 150 -µA supply current.
Suited for low-power instrumentation applications, LT6011 offers input offset voltage below 75 Ã-µV, input bias current of less than 0.9 nA, and noise voltage density of 14nV/HzÃ-½. Additional characteristics include open loop gain of 120 dB (min), CMRR of over 115 dB, and input offset voltage drift of 0.8 Ã-µV/Ã-
Read More »
Error Amplifier suits power conversion applications.
Model FOD2742 Optically Isolated Error Amplifier features tolerance as low as 0.5%. It incorporates optocoupler, precision reference, and error amplifier into 8-pin SOIC package. Unit provides isolated voltage feedback between secondary and primary sides of power conversion circuits for control and regulation purposes. Reference voltage tolerances include 0.5, 1, and 2%. Model FOD2742 has UL,...
Read More »
Traveling Wave Tube Amplifiers deliver up to 300 W.
Model 300T2G8, ranging from 2.5-7.5 GHz, provides 300 W minimum at amplifier output connector. Model 250T1G3, ranging from 1-2.5 GHz, and Model 250T8G18, ranging from 7.5-18 GHz, each deliver 250 W. All are self-contained, forced air-cooled broadband TWTAs suitable for applications that require instantaneous bandwidth and high gain. They provide power needed to ensure desired 200 V/m level for...
Read More »
Rail-to-Rail Op Amps provide low noise, 0.95nV/rtHz operation.
Model LT6200-10 features 1.6 GHz gain bandwidth product, 450 V/Ã-µs slew rate, and is stable at gains of 10 or higher. Model LT6200-5 features 800 MHz gain bandwidth product, 250 V/Ã-µs slew rate, and is stable at gains of 5 or higher. Operating on single or split supplies from 2.5-12.6 V total, units feature shutdown pin that reduces supply current to
Read More »
Advantages of Using Robotics in Manufacturing to Attract and Retain Skilled Workers
This white paper provides an overview into the advantages of using robotics in manufacturing to attract and retain skilled workers.
Read More »Fixed Gain Amplifier has differential inputs/outputs.
Available in 8-pin MSOP package, fully differential LTC1992-2 has high-stability internal gain setting resistors that provide fixed gain of 2 with better than Ã-
Read More »Optical Distribution Amplifiers handle video/audio/data signals.
Pure Digital FiberlinkÃ-® 8000 and 8100 Series transmit 1-4 and 2-12 channels, respectively, of any combination of video, audio, and data signals from one-way Pure Digital Fiberlink Transmitters. They transmit to multiple one-way Pure Digital Fiberlink Receivers without degradation to quality of original baseband signals. Both series can receive signals over multimode or single mode fiber at...
Read More »
CMOS Amplifiers suit low power applications.
Models LMV321, LMV358, and LMV324 are single, dual, and quad amplifiers, respectively. They consume supply current of 120 microamps max at 2.7 V and typically 100 microamps at 5 V. Units provide rail-to-rail output and offer supply voltage of 2.5-5.5 V. With gain bandwidth of 1.4 MHz at 5 V and slew rate of 1.5 V/microsecond at 5 V, amplifiers are suitable for portable applications such as...
Read More »Amplifier and Transponder simplify network installation.
Model A1070 Erbium Doped Fiber Amplifier consists of variable gain line amplifier with up to 25 db of gain and automatic transient suppression, which minimizes transmission penalties as channels are added/dropped in network. Supporting up to 40 channels at full gain, unit is managed through local serial port, Telnet, or SNMP. Optical transponder A1010 offers 640 km Dense Wavelength Division...
Read More »
Sensor Amplifiers are DIN rail mounted.
Sensor Amplifiers offer hi-level output signals, ready for long cable runs and/or direct interface to common PLC interface cards. They provide controlled power to associated sensor and condition sensor's return signal before providing it to output terminals. Relay buffered shunt calibration circuit offers simplified calibration, set-up, and real time circuit verification. Outputs include Ã-
Read More »
Amplifier provides signal gains of 35 dBm.
Single-Channel C-Band Erbium Doped Fiber Amplifier comes as cooled or coolerless gain block with integrated control electronics that includes laser and TEC driver circuit with alarms and monitors. Amplifier is capable of signal gains up to 35 dBm with noise of less than 4.5 dB and total output power of +10 dBm. Assembly, electrical interface, and included software bundle measures 90 x 70 x 12 mm.
Read More »
Ensure Safety, Reliability in Your Cement Plant with Aerzen Blowers and Compressors
Aerzen offers blowers and compressors for challenging cement applications such as pneumatic conveying from raw mill to raw meal silos, combustion air, cement silos fluidization, and more. At Aerzen, safety is our top priority. Check out our video to learn more.
Read More »
