Electronic Amplifiers

Operational Amplifier drives heavy loads at high output.
Electronic Amplifiers

Operational Amplifier drives heavy loads at high output.

Delivering over 1 A output current, 40 V Model ADA4870 provides wide bandwidth of 52 MHz and slew rate of 2,500 V/Â-µs to facilitate high-voltage pulses necessary to drive piezoelectric transducer in high-intensity focused ultrasound for medical treatment and procedures. In small-cell base stations and compact military radios, op amp assists with drive of power amplifier’s low impedance...

Read More »
Electronic Amplifiers

ETL Systems Debuting New RF over Fibre Design at CommunicAsia in Marina Bay Sands, Singapore

R&D experts reveal designs to address industry's fibre requirements Leading manufacturer of RF distribution equipment and British-based global designer, ETL Systems, is expanding on its product range addressing fibre applications and also its existing portfolio of superior quality RF systems. ETL is adding to its range of products which provide the highest level of redundancy whilst maintaining...

Read More »
Electronic Amplifiers

NuWaves Engineering Team Wins NASA Small Business Innovation Research Contract for C-Band Power Amplifier Development for Unmanned Aircraft Systems

Middletown, Ohio — NuWaves Engineering, an international Radio Frequency (RF) and Microwave solutions provider, announced today that the company has been awarded a Phase I Small Business Innovation Research (SBIR) contract from the National Aeronautics and Space Administration (NASA) to research and develop a linear C-band power amplifier (PA) for unmanned aircraft systems (UAS). NuWaves, in...

Read More »
Broadband 20 GHz GaN PA is designed for reliability.
Electronic Amplifiers

Broadband 20 GHz GaN PA is designed for reliability.

Fabricated on GaN, CMD184 offers bandwidth of 0.5–20 GHz, output 1 dB compression point of >+34 dBm, and flat gain of 13 dB. This broadband 20 GHz GaN power amplifier (PA) requires off-chip bias tee for proper operation. Die offers full passivation for maximum reliability and moisture protection. In addition to microwave radio and VSAT, suitable areas of use include telecom infrastructure, test...

Read More »
Electronic Amplifiers

Solid-State Power Amplifier operates in pulsed or CW mode.

Operating from 2–6 GHz, Model DM-SC50-01 offers up to 100 W peak pulsed power and 50 W average power. GaN-based broadband amplifier measures just 120 x 100 x 20 mm, excluding heat sink, and is fully customizable to meet individual specifications for electrical, mechanical, and environmental parameters. Typical applications are found in defense, aerospace, and communications industries.

Read More »
Electronic Amplifiers

Analog Devices Unveils 2.5-GSPS A/D Converter, Driver Amplifier and Rapid Prototyping FMC Module

Featuring the AD9625-2.5 A/D converter and ADA4961 RF amplifier, the module provides all hardware and software for wideband RF GSPS data converter interoperability with FPGA platforms. NORWOOD, Mass.Â- – Analog Devices, Inc. (NASDAQ: ADI), the world's data converter market share leader*, announced today immediate availability of the AD-FMCADC2-EBZ FMC module with HDL code and software...

Read More »
Electronic Amplifiers

GaN MMIC PAs suit Ka-band satellite communication terminals.

Developed with GaN HEMT power process, APN228 and APN229 provide respective saturated output power of 13 and 8 W. These broadband, 2-stage amplifiers operate from 27–31 GHz and, when integrated in solid-state power amplifiers (SSPAs), enable increased data rate in communication systems. Respectively, 16.0 mmÂ-² APN228 and 7.41 mm² APN229 provide 19.5 and 20 dB linear gain, 41.2 dBm...

Read More »
Electronic Amplifiers

AMD2012-CE3 High Voltage Amplifier

The AMD2012-CE3 is a dual output high voltage power supply with one fixed 500 volt output, and one variable output from 0 Volt to 2KV. This power supply is specifically designed for the Macro Fiber Composite (MFC) actuator. Use of the bias supply allows a range of -500 volts to +1500 volts to be applied to the MFC. The AMD2012-CE3A has a direct analog interface and the AMD2012-CE3B has a PWM...

Read More »
Electronic Amplifiers

Ultra-Low-Noise Amplifiers suit E- and W-band applications.

Measuring 1.7 mmÂ-², Model ALP283 operates from 80–100 GHz, while Model ALP275, measuring 2.125 mm², operates from 71–96 GHz. ALP283 provides 29 dB of linear gain, 2.5 dB typical noise figure, and P1dB of 3 dBm (2 mw). Delivering greater than 26 dB of linear gain, ALP275 features 3 dB typical noise figure and P1dB of 4 dBm (2.5 mw). InP HEMT MMIC LNAs are suited for W- and E-band...

Read More »
Electronic Amplifiers

Microsemi Complements Its Extensive RF Product Portfolio with New Line of Monolithic Microwave Integrated Circuit Devices

Offering the Most Comprehensive Portfolio of RF, Microwave and Millimeter Wave Solutions that Includes Wideband and Low Noise Amplifiers and Switches for a Broad Range of Applications ALISO VIEJO, Calif. - Microsemi Corporation (Nasdaq: MSCC), a leading provider of semiconductor solutions differentiated by power, security, reliability and performance, today announced its entry into the monolithic...

Read More »
Precision Fabricating with Over 40 Years of Experience
Sponsored

Precision Fabricating with Over 40 Years of Experience

Quality Sheet Metal specializes in delivering precision, value, and customer service. With a client base that spans many diverse industries and a reputation for excellence that goes back over four decades, our clients know that we can provide the optimal combination of value and flexibility regardless of the challenge. See our video to learn what we can do for you. Through investments in state-of-the-art design, manufacturing, and quality control systems, Quality Sheet Metal remains focused on maintaining a high standard of quality, customer service, and competitive pricing. With an emphasis on customer satisfaction, Quality Sheet Metal is dedicated to establishing long-term partnerships, similar to the ones they currently have with their valued clients. If you're looking for a new partner with extensive capabilities in sheet metal fabricating and finishing, look no further.

Read More »

All Topics