Master Bond, Inc.

Adhesive/Sealant contains no solvents or diluents.
Adhesives & Sealants

Adhesive/Sealant contains no solvents or diluents.

Storage-stable, one component, low viscosity system, EP19HT adhesive/sealant, impregnant, and liner features viscosity of 500-600 cps at 75°F and cures readily at elevated temperatures to tough, chemically resistant thermoset plastic. Recommended cure is 1 h at 250°F, while shorter cures can be achieved at temperatures between 325-350°F. Exhibiting minimal shrinkage upon cure,...

Read More »
A Versatile Aerospace Epoxy Conquers Cryogenic Wind Tunnel
Adhesives & Sealants

A Versatile Aerospace Epoxy Conquers Cryogenic Wind Tunnel

2/26/2009 A uniquely formulated epoxy adhesive has come to the rescue in an extraordinarily difficult cryogenic wind tunnel model bonding application. The state of the art wind tunnel poses a difficult challenge to engineering thermoplastics, not only in terms of the low temperatures and vacuum conditions, but in terms of thermal, thermal cycling and mechanical shear stresses. Cooled to...

Read More »
Potting Compound withstands temperature extremes.
Adhesives & Sealants

Potting Compound withstands temperature extremes.

With thermal conductivity of 25 BTU-in./hr-ft2-°F and volume resistivity of 1 x 1014 W cm, Type EP37-3FLFAN dielectric heat transfer adhesive works in temperature extremes, up to 250°F and down to 4K in cryogenic environments. Two-part thermal potting compound is formulated to cure at room temperatures and forms bonds that are resistant to shock, impact, thermal cycling, and chemicals.

Read More »
Clear Epoxy is for bonding and potting optical devices.
Adhesives & Sealants

Clear Epoxy is for bonding and potting optical devices.

Featuring viscosity of 700-800 cps, Master Bond EP29LP multi-purpose 2-part optical epoxy has low exotherm to peak of 120°F . It adheres to optical fibers, connectors, lenses, and glass and forms high strength bonds of more than 3,500 psi in shear. With temperature range of 60-250°F, epoxy has chemical resistance to water, fuels, acids, bases, and salts.

Read More »
One Part Epoxy Adhesive works in -60 to +450°F temperatures.
Adhesives & Sealants

One Part Epoxy Adhesive works in -60 to +450°F temperatures.

Bonding to similar and dissimilar substrates, EP13 single-component epoxy adhesive requires no mixing and has unlimited working life at room temperature. It exhibits dimensional stability, is 100% reactive, and does not contain any solvents or diluents. Able to be applied to vertical surfaces without sagging or dripping, adhesive cures within 60-90 minutes at temperatures of 300 to 350°F....

Read More »
Two Component Epoxy Adhesive cures at room temperature.
Adhesives & Sealants

Two Component Epoxy Adhesive cures at room temperature.

Available in Â-½ pint, pint, quart, gallon, and 5 gal kits, Master Bond EP30 features low viscosity, chemical resistance, dimensional stability, hardness, optical clarity, and electrical insulation properties. It is used in potting and encapsulating electronic components as well as in bonding optical elements, and has adhesion to metals, ceramics, glass, and plastics. EP30 has lap shear...

Read More »
New Cost Effective, High Conductivity Epoxy
Adhesives & Sealants

New Cost Effective, High Conductivity Epoxy

HACKENSACK, NJ - Aug 19, 2008 - Master Bond Polymer System EP79 is a novel, cost effective, silver-coated-nickel filled epoxy featuring exceptionally low electrical resistance. Volume resistivity is less than 0.04 ohm-cm at room temperature. EP79 has a convenient 1:1 mix ratio and cures readily at room temperature or more rapidly at elevated temperatures. When cured, it forms strong, tough bonds...

Read More »
Epoxy Adhesive cures in 10-15 min at room temperature.
Adhesives & Sealants

Epoxy Adhesive cures in 10-15 min at room temperature.

USP Class VI- and FDA-approved, EP41SMED low-viscosity epoxy adhesive has 5:1 mix ratio by weight. Bonds are resistant to water, oil, and many organic solvents as well as cold sterilants, ETO, and gamma radiation. It contains no solvents or diluents, adheres to wide variety of similar and dissimilar substrates, and is available for use in pint, quart, gallon, and 5 gal container kits. Shelf life...

Read More »
Epoxy Adhesive Paste resists high temperatures.
Adhesives & Sealants

Epoxy Adhesive Paste resists high temperatures.

Formulated to cure at room temperature, 2-component Supreme 11AOHT can be applied without sagging or dripping. It has mixing ratio of 1:1, operating temperature of -100 to +400°F, thermal conductivity of 10 BTU/in/ftÂ-²/hr/°F, and dielectric strength of greater than 400 V/mil. Suited for applications involving thermal cycling, product adheres to most metals, ceramics, glass,...

Read More »
Adhesive gels within 45 sec and is cured within 5 minutes.
Adhesives & Sealants

Adhesive gels within 45 sec and is cured within 5 minutes.

Formulated for general purpose bonding, Type EP50-1 produces high strength bonds with more than 2,000 psi at room temperature that are resistant to thermal cycling and chemicals including water, oil, and organic solvents. Suited for metals, glass, ceramics, wood, and vulcanized rubbers, product is approved for service over temperature range of -60 to more than 250°F. It comes in...

Read More »

All Topics