New Motors Products

Servo Motors have integral sensor module.

Models 1FK7 and 1FT6 synchronous servo motors and 1PH7 asynchronous servo motor are available with integral sensor module. Able to evaluate motor encoder signal and record diagnostics data, module transmits data to Sinamics drive converter system via Drive-Cliq interface. Motor-specific information is saved in sensor module, which incorporates servo motors into Sinamics architecture and permits...

Brushless Servomotors deliver 574 oz-in peak torque.

Series TG2300, NEMA 23 Frame, DC Servomotors provide acceleration and deceleration of loads at up to 7,200 rpm. Electromotive coil technology uses multiple precision-machined copper sheets to replace magnet wire and iron core, eliminating magnetic saturation, eddy currents, and hysteresis. Model TG2300-120-81920E delivers peak current of 70 A and continuous power density of 7.5 W/oz. Motors...

Stepping Motor/Driver Packages have harmonic gearheads.

AlphaStep Series stepping motor and driver packages with built-in feedback devices are available with harmonic (HG) gearhead. Delivering zero-backlash performance, HG gearhead enables 1.65 in.Ã-² and 1.1 in.Ã-² motor models to produce max holding torque from 22-35 and 13-17 lb-in., respectively. AlphaStep Series uses microstep control and built-in feedback device that constantly monitors...

Right Angle Gear Motors run at 1,800 rpm.

Hollow Shaft Gear Motors can be base, end, side flange, shaft, or pilot mounted. Shaft options include Ã-¾ in. hollow, along with double and single extension Ã-¾, 5/8, and Ã-½ in. diameter shafts with keys. Three AC motor options and 4 DC motor options span horsepower range from 1/8 to Ã-¼ hp with gear ratios from 5:1-60:1. Gear motors are all ball bearing and synthetic oil...

Specifying Removable Insulation Blankets - A Guide for Engineers

Looking for guidance on how to spec removable insulation? Download our free guide for engineers now!

Brushless DC Motor produces high power in limited space.

With operating voltage of 28 V, Model 000-0362 is capable of delivering in excess of 45 oz-in. of continuous torque. It features 1.85 in. profile and 4.2 in. diameter. Motor utilizes Hall-Effect sensors and achieves 85% efficiency at load point. Custom mounting configurations and variety of electrical options are available to meet specific requirements.

Step Motors suit marine and submarine applications.

Submersible Series Stainless Steel Step Motors are internally sealed, eliminating corrosion and motor failure in fluid processing, washdown, and submersion environments. Standard washdown motors are partially filled with oil to prevent liquid ingress, while motors intended for complete submersion are filled with oil and are pressure-compensated. Submersible motors come in 23, 34, and 42 frame...

Parallel Shaft Gearmotor incorporates 14 gear ratios.

Model PS1900 offers gearing ratios from 5-to-1 up to 320-to-1. Motor features continuous-duty torque ratings up to 125 lb-in. and compatibility with all Groschopp AC, PM, and DC brushless motors. Synthetic lubricants provide better heat dissipation and enable motor to withstand repeated starts and stops as well as continuous torque. Internal ball bearings and needle bearings on output shaft...

Motors come in stainless steel and washdown versions.

Washdown Super-EÃ-® Motors are available in TENV and TEFC enclosures from 1-20 hp in NEMA frames 56C through 256TC. They are suited for food processing and other applications that expose motors to high-pressure washdown. All Stainless Super-Es come in TENV and TEFC enclosures and range from 1-7Ã-½ hp in NEMA frames 56C through 213TC. With external surfaces made of 300 series SS, they are...

Synchronous Motors offer speeds to 30,000 rpm.

Designed for operation with bus voltages to 750 V, IndraDyn H kit motors are optimized for high torque and consist of 3-phase-wound stator and permanent-magnet rotor. They combine advantages of synchronous motor technology with operational characteristics of asynchronous motors, providing up to 6,500 Nm torque. Cooling system is enclosed within stator, and motor windings are protected against...

Brushless DC Motor features plastic construction.

At 4 V, low inertia, outer-rotor DC motor draws less than 100 mA at 1,400 rpm. Measuring 1.85 in. diameter by 0.75 in. tall, unit features through-hole design, optional integral drive electronics, and integral encoder option. Low-profile provides space-efficient, direct coupling interface in many applications. Motor is suited for portable or battery-operated polygon scanners as well as diagnostic...

Acoustic and Thermal Solutions for Original Equipment Manufacturers

Technicon's products solve the most complex noise pollution and thermal problems and improve product marketability. Check out the video to learn more.