New Circuits Products

Integrated Circuit acts as programmable logic controller.

PLC on a Chip(TM) is programmed by EZ LADDER PC-based software. Single-chip design can be embedded into OEM products to allow for ladder diagram and function block programming. It also provides control over I/O, counting, and serial communications. Development kits are available that include library of pre-designed, drop-on circuitry for I/O, power supply, and other supporting components.

Smart Card IC features 256 kbyte of pure flash memory.

Model EMTCG256-3G is compatible with ISO7816-3 Integrated Circuit Card specification, and operates with power supplies from 5-1.8 V. It features 8-bit 8051 microcontroller core, internal tamper-proof clock that operates up to 30 MHz, and built-in analog sensors. Flash memory is partitioned into 3 sections: 128 kbyte of OTP memory and 64 kbyte of EEPROM, plus 32 x 2 kbyte blocks of flash memory....

DC/DC Buck Controllers achieve up to 96% power efficiency.

Packaged in 16-pin, TSSOP PowerPad(TM) package, TPS40070 and TPS40071 synchronous ICs include voltage feed forward topology and support input voltages from 4.5-28 V. They leverage proprietary Predictive Gate Drive(TM) technology and facilitate circuit design in non-isolated power systems. User-programmable power-supply features include under-voltage lockout, soft-start, high-side short-circuit...

CMOS Serial Link increases backplane port density.

Model TLK6B008 enables 6 Gbps transmission over legacy system that run up to 3 Gbps. It has eight 6.25 Gbps bi-directional serial data channels on sharp end and sixteen 3.125 Gbps channels on blunt end, providing 100 Gbps data throughput. Receiver uses 4-tap adaptive DFE receive equalizer technology, including cancellation of first post cursor. Transmitter uses 4-tap equalizer with fully...

A Guide to Preventive Maintenance & Refurbishment of Your Tablet Press

Check out this guide to keeping your tablet press in good working order.

Motor Control IC works with brushless DC motors.

Packaged in compact 64-pin PQFP, model MC73110 consists of intelligent, single-axis controller designed to provide digital current loop, velocity loop, and commutation for motors. It operates in one of 3 modes: internal velocity profile mode, velocity mode with external command signal, and torque mode with external command signal. Unit provides 6-step and sinusoidal commutation, analog/digital...

Motor Driver IC comes in thermally enhanced package.

Series A3949SLP and A3949SLB DMOS full-bridge motor driver IC suits DC motor applications. Unit operates with single supply and with output rating of 36 V at 2.8 A. Driver is offered in small outline, 16-lead thermally enhanced TSSOP package measuring 5.0 x 4.4 mm. PHASE and ENABLE input terminals control speed and direction. Low rDS(On) DMOS outputs are combined with internal synchronous...

Synchronous Buck Driver works with DC/DC converters.

Offered in HTSSOP-14 PowerPAD(TM) packages, UCC27223 driver utilizes Enable pin and proprietary Predictive Gate Drive digital control technology to reduce diode conduction and reverse recovery losses in synchronous rectifier MOSFETs. Employing closed loop feedback system that detects body-diode conduction, Predictive Gate Drive adjusts dead time delays in next switching cycle. It also has Ã-

High-Density FPGAs offer design flexibility.

Industrial-grade Stratix(TM) FPGAs, models EP1S80 and EP1S60, promote design flexibility in military, aerospace, and industrial systems. Model EP1S80 provides 79,000+ logic elements and 7+ Mbits of internal memory. Offered in industrial (-40 to +100Ã-ºC) and extended temperature (-40 to +125Ã-ºC) versions, Stratix devices are built on 0.13 micron, all-layer copper process. They feature...

CMOS Bus Switches suit hot-plugging applications.

Pin-compatible with existing TTL parts, 20 bit, dual-port switches operate from supply voltages of 4-5.5 V. They have power-down protection on inputs and outputs and offer latch-up immunity and ESD protection to 2 kV. Off resistance and On resistance, typically rated at 2-25 ohm, maximize isolation when Off and minimize loading when On. Power dissipation is typically 1 Ã-µA. Devices are...

Triple Video Driver offers HD/SD filtering capability.

Selectable for High Definition (30 MHz) or Standard Definition (8 MHz) signal filtering, FMS6418A removes high-frequency noise prior to digitizing signal or artifacts introduced during D/A conversion in encoder for RGB or YUV signals. Video filter, available in 16-pin SOIC package, has triple 6th order filters and combines 2:1 multiplexer on each filter channel with filtering and output drive...

Precision Machining Solutions with Over 25 Years of Experience

Quality, customer service, and unbeatable value are the hallmarks of Hogge Precision. Since 1989 we have built a reputation as the go-to precision machining source, servicing many demanding industries. For CNC machining and screw machining, there are few manufacturers that can match our capabilities and expertise. See our video to learn more.