New Agricultural & Farming Products Products

Bulk Bag Filler is USDA accepted.

Twin-centerpost(TM) unit provides product contact surfaces that are constructed and finished in compliance with 3-A standards. Available with primary bag filling components and material delivery system, filler is constructed of 304 stainless steel. It is equipped with manual fill-head height adjustment, pneumatically retractable bag hooks, inflatable cuff, and feed-chute outlet port. Unit is...

Mini Stock Picker provides safe overhead access.

Model 9MP offers 15 ft working height, 500 lb total platform capacity and maneuverability using four 6 in. swivel casters. Side entry platform includes self-closing entry gate. Picker comes with maintenance-free battery, automatic 5 hr battery charger, and aluminum mast sections with guide system. Safety features include lanyard attachment anchor, 2 emergency stop controls, amber warning beacon,...

Refrigeration Control Module features optional transformer.

Chillgard LC Control Module, with transformer option, enables unit to power up to 6 remote Chillgard LS Photoacoustic Infrared Refrigerant Monitor sensors. Standard powering uses 24 Vac/dc. Unit works with Chillgard LS Refrigerant Monitor gas sensor modules to provide remote signaling and control capability in refrigerant monitoring applications. It communicates with up to 8 sample points from...

Order Picker provides efficiency and safety.

Model SSCM Stock Selector allows user to lift, lower, forward, and reverse from stock picking level. All controls are located on elevating operator compartment and platform, allowing complete maneuverability. Maneuverable 32 in. wide unit is able to go into areas where only rolling ladders were previously used. Stock Selector is also suitable for overhead applications, such as changing lights and...

Saving Energy with Efficient Belt Drives

By introducing energy efficient belts on electric motor drives, you can implement a simple, cost-effective solution to achieve energy savings in your facility.

Stator Removal Tool facilitates pump maintenance.

Stator Removal Device is designed to be portable within plant facility and is for use at either pump location or in maintenance shop. It enables single maintenance person to remove and replace large stators and rotors, minimizing downtime. Tool is compatible with company's medium to large pumps and pump stators.

Mower Deck suits commercial capplications.

Made of seven-gauge steel, ZD-Pro shaft-driven deck is available in 60 or 72 in. cutting widths. Measuring 5.5 in. deep, it allows airflow circulation through blades. Unit's cut and re-cut system provides small grass clippings and generates clean appearance. Cutting height can be adjusted from 1 to 5 in. (in -½ in. increments). Deck also incorporates double V-belt with cast iron pulleys, swivel...

Die Cutter cycles at 90 hits per minute.

Small Format Web-Fed Die-Cutter cycles at high speed, making it an economical alternative to large-format die-cutters. The 12 in. x 16 in., 20 ton die-cutter is optically registered for cutting accuracy, and can thermal die-cut, emboss, deboss, hot and cold steel-rule die-cut and steel-rule kiss-cut. Unit is custom built for compatibility with existing plant equipment.

Laser Controller acquires all necessary analog signals.

LCON series Configurable System-on-a Chip (CSoC) laser controller acquires optical power, reflected power, temperature, and laser diode current signals. It can process and react to data in less than 5 Ã-µs, resulting in 200 kHz response rate. With reconfigurable hardware and firmware, series has system memory capacity with 2 MB FLASH, 8 MB SDRAM, and 8 KB EPROM. Adaptive TEC temperature...

Electrical Control Station is used for training purposes.

Training and testing center is comprised of stand alone panel that contains functioning electrical schematic that permits user to change control circuitry to experiment with new configurations. Measuring 4 x 8 in., panel includes banana clip style connectors, stop/start circuits, on and off relay delays, control relays, selector switches, load cells, digital indicators, temperature probes, and...

Die-Cutting System handles delicate materials.

Multiple Roll Die-Cutting System handles nonwoven roll material with low-tension pull to avoid stretching. Webs from multiple rolls are brought through ultrasonic welder (to combine material) and inkjet printer (to print part numbers and lettering). Optically registered, belt-fed die-cutter cuts out finished parts, which are then removed from belt onto conveyor for operator collection.

Locon Sensors Withstand Extreme Temperatures

Locon Sensor Systems offer robust sensor solutions for even the most severe environmental conditions. Their line of high-temp inductive sensors and their cylindrical photoelectric series can operate in temperatures up to 250 degrees Celsius. See our video to learn more.