Indoor Photo Sensor offers local or global modes.
Intended for daylight harvesting, Series GR 2400-iPC offers local and remote adjustments including time delay, trim, baseline, and dimming curve. Local Photo Sensor, Model GR 2400-iPC-L is used with MicroPanel integrated distributed control panels, which have on-board photo sensor inputs. Global Photo Sensor, Model GR 2400-iPC-G, when combined with photocell card, has up to 14 trigger points,...
Read More »
Toxic Gas Sensors provide protection in hazardous areas.
TS Series senses hydrogen sulfide (H2S) gas over 0-100 ppm range and offers adjustment-free calibration. Electrochemical cells operate over -40 to +50Ã-
Read More »Navigation Sensors help automate inventory tracking.
NavPax Sensor Units integrate 3-axis MEMS gyros, accelerometers, compass, signal processing, and GPS information to provide complete package for real-time, land-based vehicle tracking solutions. They are used as part of RFID-aided warehouse tracking system that tracks position of each forklift, unique cargo identification, and pick-up and put-down locations of inventory with accuracy to 99%.
Read More »
Laser Copy Counter is suited for printing applications.
Designed for use on newspapers, magazines, and other printed media in publishing and other industrial applications, SCATEC-J copy- and edge-counting, non-contact laser sensor can also be used in applications involving lap or shingle stream edge counting. Unit counts multi-colored, thicker printed items, detecting packages as thin as 1.5 mm at rates to 280,000 pieces/hr. Measuring range is 0-55...
Read More »
Top Design Engineering Considerations For Optical Assemblies
In this eBook, we provide an overview of the design engineering considerations to keep in mind when planning the manufacture of an optical assembly.
Read More »Load Cell facilitates brake testing.
Designed with 3 in. diameter flat loading surface, Brake Pedal Load Cell measures force where direction of load changes. Set of tapped holes on underside and mounting bracket allow it to be firmly attached to pedal. Load cell gives same output, Ã-
Read More »Accelerometers measure vibration in 3 orthogonal directions.
Triaxial ICPÃ-® Ceramic Shear Accelerometers, Series 354B, includes 3 models, each with 3 hermetically sealed, titanium-cased, single-axis sensors mounted on hard anodized mounting block. Each sensor features three 10-32 coaxial connectors. Offering sensitivity of 2.5, 10, and 100 mV/g with measurement range of 2,000, 500, and 50 g, respectively, accelerometers include microelectronic signal...
Read More »Portable AC Voltage Detector has pocket-sized design.
Fluke 1AC-II VoltAlert(TM) and Fluke 1LAC-II VoltAlert are CAT IV, 1,000 V overvoltage-rated units that enable users to test for energized circuits and defective grounds by touching tester tip to terminal strip, outlet, or cord. Incorporated VoltBeat(TM) technology provides continuous self-test capability, which scans for battery performance and circuit integrity and indicates if device is...
Read More »
IR Temperature Sensors feature teachable technology.
Non-contact, passive T-GAGE(TM) sensors detect objects that are hotter or colder than ambient condition and trigger output. Set-up is facilitated via Manual or Dynamic TEACH-mode push-button programming, which requires no potentiometer adjustments. Able to operate even if product is not moving, sensors detect temperatures from 0-300Ã-
Read More »
X-Ray Detector suits protein crystallography.
Designed for macromolecular X-ray crystallography, ÃÆ'ââ¬-¦XIOM 200 has essentially zero detector noise, and is able to record each individual X-ray photon as it strikes detector. By eliminating readout dead-time, imaging system supports continuous scans where goniostat is scanned without stopping between frames. Active area of 200 mm diameter and high spatial resolution allows large...
Read More »
Miniature Sensor determines attitude and heading.
Equipped with solid-state inertial sensors and earth-magnetic field sensors, MTi Inertial Measurement Unit provides drift-free, gyro-enhanced Attitude and Heading output with 0.5Ã-
Read More »
Standex Engraving Mold-Tech Offers Nickel Shell Capabilities on a Global Scale
Standex Engraving Mold-Tech is the premier, global supplier for mold texturing and surface finishing. With a full range of services, Standex Engraving Mold-Tech is also the only nickel shell supplier producing in three global locations. See our video to learn more.
Read More »
