New Motor Controllers and Drives Products

Digital Control Chip requires no programming.

With CLOZD(TM) Loop Controller, user selects desired control configuration through pin settings and closes loop around power supply, motor drive, heater, lamp, fan, valve, or TEC. Output drive is automatically adjusted until measured feedback signal matches desired setpoint command. System time constants ranging from 128 Ã-µS to 1,074 sec can be controlled with 12-bit resolution. Output drive...

Dual Voltage DC Drive includes speed and torque controls.

Capable of operating in speed or torque control mode, MM23002D series dual voltage drives are available in NEMA 1 and 4X models with wired and mounted operators and switches on front cover and AC line fuses inside. User-selectable inhibit modes enable users to choose whether inhibit function is activated by NO or NC condition. Jumper selects whether inhibiting directs motor to min speed or stop....

Isolated DC Drive can control DC motors up to 2 hp.

Housed in NEMA 4X enclosure, Patriot Model MC10-PCM accepts any 0-10 V or 1-5 mA reference signal. Shunt resistor terminals are provided in case 4-20 mA or other current signal is to be used. Drive includes power and current limit LEDs, line fuses, and inhibit pins for remote start/stop control. Mounted on cover is speed adjust knob, on/off switch, and manual/signal switch. Drive has 1% speed...

Modular Drives offer 98% operating efficiency.

Models VLT 5122/5302 are 90-200 kW, 125-300 hp drives are available with built-in RFI performance to EN 55011 class B. Power termination design accepts single box lug or dual cable legs. Logic routing includes tie-down provisions to simplify installation and protect against noise disturbance. Ambient temperature ratings are 40-45Ã-

Material Selection Guide: High & Low Density Polyethylene

In this eBook, learn about high-density and low-density polyethylene's similarities, differences, and practical applications from New Process Fibre.

PWM Dual Voltage AC Drives include isolated front end.

Series VFD05-D230-PCM features minimum speed adjustment potentiometer, DC injection braking, and automatic or manual restarts. Available to 1.5 hp, drives can be used with 3-phase induction, single-phase PSC, shaded-pole, and synchronous motors. Doubling jumper can be set to output 230 Vac when only 115 Vac power supply is available. With automatic restart, inverter will restart after low voltage...

Variable Speed Drive features swinging choke technology.

Model ACS550 precisely controls motor speed to reflect actual demand, eliminating waste caused by fixed-speed operation. Swinging Choke reduces harmonics at both full and partial loads. Standard Start-Up Assistant software guides user through set-up procedures, while Maintenance Assistant signals when it is time for routine maintenance. Diagnostic Assistant provides suggestions for correcting...

Volts/Hertz AC Drive features isolated front end.

Dual voltage Model VFP4X04-D230-PCM includes minimum speed adjustment potentiometer, DC injection braking, and automatic or manual restarts. It can control variety of motors including 3-phase induction, single-phase permanent split capacitor, shaded pole, and synchronous motors. Doubling jumper can be set to output 230 Vac when only 115 Vac power is available. Offered to 1 hp, drive comes in...

Motor Control IC works with brushless DC motors.

Packaged in compact 64-pin PQFP, model MC73110 consists of intelligent, single-axis controller designed to provide digital current loop, velocity loop, and commutation for motors. It operates in one of 3 modes: internal velocity profile mode, velocity mode with external command signal, and torque mode with external command signal. Unit provides 6-step and sinusoidal commutation, analog/digital...

Step Motor/Driver offers optional built-in encoder.

SilverPak 17 is a NEMA size 17, 2-phase, 1.8Ã-

Microstepping Drives offer servo-like performance.

Series P7000 Drives use multi-step positioning to convert full step indexing commands into smooth microstepping resolution. They provide Encoderless Stall Detection(TM), down to and including rest, without use of separate feedback device. Available for AC or DC operation, Series P7000 can power any 2-phase NEMA step motor. Current auto-tuning techniques make units suited for single or multi-axis...

ISO-Certified Precision Machining and Contract Manufacturing Services from DFF

DFF is an industry leading contract manufacturer specializing in medium to high production precision machined components and electromechanical assemblies. Our 100 CNC machining centers and design-assist capabilities ensure our customers' needs are always met. Check out our video to learn more.