Machining Center provides drilling, tapping, and milling.
Mill Drill Center offers 12 x 10 x 12 in. work cube and 15,000 rpm 40-taper spindle, powered by 15 hp vector drive system. Ballscrews and high-torque servo motors on all axes provide rapids to 2,400 ipm and accelerations to 0.8 G. Automatic tool changer stores up to 20 tools and changes them in 1.5 seconds. Dual fixture stations allow operators to load and unload parts on one fixture while...
Read More »
Machining Centers work in five axes.
VR Series 5-axis profiling vertical machining centers make complex shapes, undercuts, and difficult angles. Travels are 64 x 40 x 30 in. for VR-8, 64 x 40 x 30 in. for VR-9, and 120 x 40 x 30 in. for VR-11. Each has dual-axis spindle with fully enclosed gimbal to protect gears from chips and coolant. VR head provides +/-32 deg of travel on A and B axes for complex geometries and undercuts. All...
Read More »
Vertical Machining Center has Fanuc Motion Control System.
Richmond 40 taper VMC 1000 weighs 10,000 lb, has cast-iron base, column, and saddle for dampening and rigidity, and uses dual supported, pre-tensioned 40 mm ballscrews that deliver repeatability of 0.0001 in. It has 1,181 in./min rate, 8000 rpm spindle, Fanuc control, and 15 hp spindle drive motor. Spindle has wrap-around coolant sleeve, grease-packed trucks and caged rollers for long life....
Read More »
Machining Centers offer various speeds.
DIGMA VMC offers 1.7 g acceleration, 42000 rpm and 1576 ipm travel. Spindles have multi-temperature sensors for spindle length compensation through machining process. Mach CNC 647 is for short and long runs of parts up to 1/4 in. dia. It has 12000 RPM rotating toolhead, 4 independent cutting tools, and backworking capabilities. K'MX Swing 1026 Swiss turning center has 26 mm bar capacity, main and...
Read More »Adhesive Tapes for Energy & Utility Applications
Read about the various types of tapes used in energy and utility applications.
Read More »
Trunnion Machine adapts to changing needs.
High Performance Trunnion (HPT) Machine features sliding spindle carriers that allow most cutting tools to be changed outside machine base in less than 1 minute. HPT is available with spindle horsepower of 5, 7.5 and 10 HP. Eight workholding stations are standard, and each is equipped with 2-jaw chuck that can use interchangeable top jaws. Control system uses IndramatÃ-® CNC and...
Read More »
Horizontal Machining Center suits high volume production.
F3-660L offers spindle speeds from 0 to 20,000 rpm in 1.55 sec, 3.2G acceleration/deceleration rates, 90 deg table indexing at 0.8 sec, and chip-to-chip time of 2.4 sec. Rapid traverse rate for X, Y, and Z axis is 4720 ipm. Strokes for X and Y axes are 26 in.; Z axis stroke is 20 in. Tool magazine stores 40 tools with No. 40 taper. Tool life management software, 2-pallet changer, flood and base...
Read More »Multiple Profile System changes tools in 0.5 seconds.
MPS 08 Multiple Profile System allows users to machine semi-finished stock up to 10 meters long. It accepts semi-finished round bars, square bars, tubes, angle profiles, or bent profile materials. Two synchronized NC fixtures can rotate workpieces at up to 50 rpm. Installation area is less than 20 sq ft, and MPS 08 may be adapted to standard machining centers. Chip-to-chip times are clocked at...
Read More »
Multi-Tasking Machine combines machining and turning centers.
Integrex e-410H offers milling spindle with B-axis, C-axis and X, Y and Z-axes. 35 HP main and second spindles, with full C-axis, operate at up to 4,000 RPM and deliver 470 ft-lb of torque. B-axis has 240 deg travel range and performs full 5-axis contouring. E-mail communication through cell-phone link offers instant notification of machine alarm or production status. Fusion 640M Pro CNC system...
Read More »
Horizontal Machining Center produces near-dry chips.
HORKOS HFN-R40H machining center, with Minimum Quantity Lubrication (MQL), consumes just 20 to 50 mL per hour and minimizes concerns associated with cutting fluids when drilling, reaming, boring or tapping. It has 40-taper spindle and 20.8 x 22.0 x 20.8 in. work area travel. Rigid z-axis ram carries 5.5, 7.5, or 15 kW, 12,000 or 15,000 rpm direct-drive spindle. Machine has automatic tool changer...
Read More »
Horizontal Machining Centers are FMS system-ready.
HU50-5AX tilting trunnion table type machine accommodates part dia up to 27 in. and weights up to 1430 lbs. 50 taper spindles are available with up to 12,000, or 15,000 rpm and 40 taper up to 20,000 rpm. HU40T features max part dia of 20 in. 40 taper spindles are available with up to 12,000, 15,000, 20,000 rpm or 30 taper up to 40,000 rpm. Both machines hold 0.00012 in. true position through all...
Read More »
Clear Clogged Drains Faster with General Pipe Cleaners' Kinetic Water Ram
The Kinetic Water Ram by General Pipe Cleaners clears out clogged pipes quickly using kinetic energy. The Ram is so simple to operate, anyone can use it. Check out the video to learn more.
Read More »
