Fives in Metal Cutting and Composites
Paris 75009 FRA
Share:
Industrial Gauging Sensor suits automotive applications.
Built to NEMA-4 standards, single point, non-contact Class II SLS5000 sensor employs integrated sensor and built-in processor for data averaging and filtering. Dynamic laser feedback loop allows accurate measurement, regardless of general plant environmental conditions. Sensor makes virtually error-free measurement with reliability and repeatability of up to 16,000 times/sec. Measurement range is...
Read More »
Urethane requires only one coat.
High-build, fast-drying, direct-to-metal Fast Clad(TM) DTM Urethane can be applied at 6-9 mils DFT in single coat with no outgassing or pinholing. Urethane dries in 1 hour as corrosion-resistant finish and may be applied at temperatures as low as 35Ã-
Read More »
Oscillate Winding System offers up to 12 stations.
Model 630 PMC winds ferrous and non-ferrous metal strips directly from slitter and can be used in heavy-duty rewind applications. Individual winding stations, coordinated through Accu-Wind computer control system, offer cantilevered shafts for supporting spools or cores weighing up to 3,500 lbs. Each is equipped with 10 hp, 4-quadrant regenerative drive, capable of providing 150 lb material...
Read More »
Concrete Repair Kit fixes cracks and gaps in minutes.
FlashPatch(TM) system allows heavy forklift traffic to resume within 15 minutes after application of product. Low-order product meets USDA requirements and works at substrate temperatures as low as as 20Ã-
Read More »
DC-AC Inverters power large LCDs.
Dimmable Series 8mAD 2-tube inverters power LCDs in 10.4 and 12.1 in. diagonal size range that are backlight by one pair of CCFLS (cold cathode fluorescent lamps) in conjunction at either end of LCD panel using one output connector. Inverters offer on-board connectors and can be dimmed to less than 5% duty cycle using external analog control signal or external PWM generator. Products measure less...
Read More »
Servo Motors handle frequent stop/start applications.
Series 22-100 DSD 3-phase, 540 V, synchronous servo motors, are available in sizes 22, 28, 36, 45, 56, 71, and 100. Units can be configured with or without fans and can include standard or high-resolution encoder and power connectors. Torque ratings vary from under 5 N-m to 300 N-m max. Torque overload capability is rated up to 300%. Inertia ratings vary from 18,000 JsecÃ-² to 110,000+...
Read More »Data Loggers feature push-to-start button.
Pro Series is offered in 2 models: Model TR220 for temperature and humidity and Model SR200 for temperature. They provide data storage of 32,512 sample points, and accuracy of Ã-
Read More »
Collet Chuck supports large bar stock.
Full BoreÃ-® mechanical-grip, air-release, front-mounted collet chuck eliminates conventional draw tube and external actuator. Spring force holds workpiece while it is being machined, and part remains clamped even if air pressure is lost. Adjustable concentricity and dead-length positioning allow hex, round, and square bar feeding. Clamping force is constant regardless of spindle speed. Pads...
Read More »
Pulse Energy Head offers damage threshold to 193 nm.
Model PE50HD Pyroelectric head provides energy measurement of high-energy Excimer lasers. It is calibrated for 157 nm and 10.6 Ã-µm. Linearity is specified at 1% for 0-400 Ã-µS pulse widths, with pulse width measurement capability up to 1 mS. Energy scales include 10 J, 1 J, 100 mJ, and 10 mJ. Max pulse rate is 100 Hz, while calibration accuracy is Ã-
Read More »
Processor Board accommodates 2 expansion modules.
Low-power 3U CompactPCI CP321, with Motorola Kahlua II PowerPC processor for mission-critical industrial or military applications, has two 32-pin DIP sockets that permit memory expansion using DiskOnChip, Flash chip, or SRAM. Operating at up to 330 MHz and packaged in 3U/4HP design, board accommodates up to 256 Mbyte of soldered SDRAM at 133 MHz, and 8 Mbyte of soldered Flash memory for boot code...
Read More »