Aprima Medical Software, Inc
Carrollton, TX 75006
Share:
Jobber Drills are TiN coated.
Series A002 high-speed steel jobber drills, with TiN coating on working end and special point geometry and helix, allow for lower cutting forces than standard design, while resisting flank and crater wear. Drills are offered in metric and fractional sizes, ranging from 1.00 to 16.00 mm and 3/64 to 5/8 in., respectively.
Read More »
Acrylic Coating applies directly to metal siding.
BOND-PLEX WB single-component, waterborne, acrylic-resin coating, for interior or exterior use over pre-finished metal siding, eliminates need for primer. It may be applied to fluorocarbons such as Kynar, polyester polymers, and silicone polyesters, or when low-sheen finish is required to match existing coil-coated metal siding. Low-VOC coating has low odor and dries to mar-resistant finish. It...
Read More »
Conveyor Parts Washer has modular design.
Model 600 can include rinsing, air-knife blow-off, and drying. System is offered with Allen-Bradley PLC, variety of sensors and fault indicators, and touch-screen interface. Tanks and process chambers are fabricated from 304 stainless steel, allowing flow-through washer to be used with aqueous spray cleaning chemistries without corrosion. Stainless mesh belt, from 16 to 24 in. wide, transports...
Read More »
Truck Step provides access to cargo.
Compact SAF-T-Step, single step retractable ladder with removable hand rail, mounts in flat position on inside of truck tailgate. It manually unfolds into step position to provide access to cargo beds of commercial and industrial pick-up trucks and other similar vehicles. Made of heat treated cast aluminum alloy coated with non-slip paint, it withstands up to 400 lb. Step is compliant with safety...
Read More »
Coil Grab includes built-in crane scale.
Motorized Rotating Coil Grab is equipped with continuous belt edge protector modules, dual plunger safety saddle trios, and front and rear rollers. Crane scale can be read directly on lifting device or remotely at base station. Weight data can be interfaced to other computer data as desired. Applications include steel warehousing facilities, steel mills, aluminum mills, stamping plants, and other...
Read More »Gearboxes raise output torque by up to 47%.
UNICASE(TM) Helical In-Line Gearboxes, from models SK 02 through SK 53, are available in 6 case sizes as single-reduction to sextuple-reduction drives, in foot or flange mounted units. They operate at up to 98.5% efficiency and offer torque up to 19,744 lb-in. Power ranges from .16 to 30 HP; output speeds are from 1 to 986 rpm; and gear ratios range from 1.24:1 to 14340.31:1. One-piece housing...
Read More »Angle Valve handles liquids, gases, and steam.
ARES pneumatically actuated on/off valve works in maximum pressure of 232 psig for most media and 150 psig in steam applications. It is available with clamp, NPT, and weld end connections from 3/8 to 2 in. Actuator has NAMUR style mounting pad, visual position indicator, and is available in spring-to-close, spring-to-open, and double acting configurations. Accessories include limit switches,...
Read More »
Miniature Ball Screw includes spring-preloaded double nut.
Series 1510 compensates for torque variations due to inaccuracies in ground thread. Diameters range from 3 to 16 mm with pitch down to 0.5 mm. Standard nut body is cylindrical with attaching thread. Applications include semiconductor production machines, inspection equipment, microscope stages, and miniature robotics. Series 1530 offers rolled thread for less demanding positioning applications....
Read More »
Manifolds offer fully automatic operation.
VM 1000 Series is designed for use with liquid cylinders, while VM 2000 Series is used with high-pressure cylinders. Both give uninterrupted supply of gas as primary bank of cylinders is depleted. At preset pressure, switchover unit automatically switches to reserve bank. VM manifolds operate on 115 Vac power, but will continue to function during power failure. They meet or exceed NFPA system and...
Read More »
Rack System provides mobile pallet storage.
PushBack Rack System is based on the use of overriding, wheeled pallet carts that travel on slightly canted rails, allowing carts to roll forward to front of bay. System configurations range from 2 to 6 pallet positions deep, with variable bay widths to accommodate single-wide or double-wide pallet rows. Upright frame is 1-piece construction, made from 50,000 psi steel, with horizontal and...
Read More »