Wacker Chemical Corp.    Chino, CA 91710
Dec 02, 2011 Formulated with catalyst that does not use organotin compounds, SILPURAN® 4200 is safe to use from health standpoint. Single-component silicone rubber adhesive is certified as biocompatible in accordance with selected ISO 10993-1 and USP Class VI tests. Upon vulcanization, SILPURAN® 4200 forms silicone elastomer with optimal mechanical strength. Pasty, self-leveling compound shows shear thinning behavior, can be applied manually or automatically, and is cured by exposure to air moisture.

Avery Dennison    Pasadena, CA 91103
Nov 28, 2011 Supplied as acrylic-coated polyurethane film on polyester release liner, MED 5567A provides manufacturers of temporary adherent medical devices with alternative to acrylic adhesives and rubber-based hydrocolloid dressings. Breathability and absorbency promotes fluid handling capacity (FHC) without compromising adhesion properties and moisture vapor transmission rate characteristic of acrylic adhesives. Overall thickness is 125 µm, and transparent solution conforms to skin contours.

Master Bond, Inc.    Hackensack, NJ 07601
Nov 22, 2011 Formulated for bonding, sealing, and coating, UV16 single-component, no-mix system cures in 1 min or less at room temperature with commercial UV light sources. This 100% reactive epoxy, uninhibited by oxygen, does not release any solvents or volatiles during cure. Cured in thicknesses up to 0.125 in. with 2%-3% shrinkage rate, solution delivers tensile strength exceeding 4,100 psi and Shore D hardness greater than 75. Product has viscosity of 200-400 cps and adheres to array of substrates.

Henkel Corporation    Rocky Hill, CT 06067
Nov 11, 2011 Comprised of resin and hardener, Germanischer Lloyd (GL)-approved Macroplast® UK 1340(TM) prevents crack propagation on wind blades and delivers long-term structural integrity on turbine assemblies. Two-part adhesive, when mixed, cures in 60-80 min at temperatures to 75°C. Cured product demonstrates tensile shear strength exceeding 20 MPa at -40 to +80°C and Tg of 65°C and higher. Dynamic fatigue strength lets wind blades handle deflection, dynamic load, and stress on adhesive bond line.

Pres-On Products, Inc.    Addison, IL 60101
Nov 11, 2011 Featuring pressure-sensitive acrylic and silicone adhesive, respectively, S-500 and S-700 are primarily used to seal out environmental hazards from electrical, communications, and HVAC enclosures. Both products, which combine lightness of foam and sealing strength of sponge rubber, resist UV light, ozone, and extreme temperatures. UL recognized for flame retardance, tapes can also be used to isolate vibration in electronic components and vehicles.

American Standard Circuits, Inc.    West Chicago, IL 60185
Nov 09, 2011 Electrasil-3A bonds PCB ground plane with heat sink for RF circuits and electromagnetic shielding applications. Silicone-based elastomeric interface is suitable for bonding surfaces that have widely dissimilar values of CTE. Electrasil-3A can be supplied as bonding sheets of any uniform thickness starting from 3 mils and higher, or as putty material that can fill circuitry with complex shapes that are not necessarily planar.

Aremco Products, Inc.    Valley Cottage, NY 10989
Nov 08, 2011 Resisting temperatures to 3,200°F, Ceramabond(TM) 503 is applied by brush, spatula, or syringe and cures fully in 1-2 hr at 700°F. Inorganic, water-dispersed, aluminum oxide filled adhesive can achieve tensile-shear strength of 900 psi by curing further at 1,000°F. Inert and chemical resistant, Ceramabond 503 will not outgas in ultra high vacuum. Product features volume resistivity of 109 W-cm and dielectric strength of 250 V/mil.

Avery Dennison    Pasadena, CA 91103
Oct 19, 2011 Designed to withstand high heat and pressure challenges associated with electronic parking brakes, EPB Adhesive offers optimal damping at 212°F, and resists adhesive bleed at temperatures greater than 302°F and pressures greater than 200 bar. In addition, brake shim adhesive enables long-term service while minimizing noise, vibration, and harshness.

Aremco Products, Inc.    Valley Cottage, NY 10989
Oct 17, 2011 Consisting of ceramic and iron oxide filled paste, Pyro-Putty® 2500 bonds, seals, and repairs defects up to ¼ in. in cross-section in cast iron and steel components up to 1,600°F. Single part, water-based, black-pigmented paste will not decompose at high temperatures and contains no VOCs. Setting at room temperature and curing in-situ or by heating to 200°F for 2-4 hr, product is suited for afterburners, boiler casings, heat exchangers, exhaust manifolds, flanges, headers, and mufflers.

Bayer MaterialScience, LLC - Coatings, Adhesives & Sealants    Pittsburgh, PA 15205
Oct 14, 2011 Used for restoring water slides, polyaspartic gelcoat technology has life expectancy of years and dry times that accelerate return-to-service - sometimes as soon as 24 hr. Low-odor product is formulated for optimal durability, weather-ability, color and gloss retention, and ultra-low VOC content. This spray-applied, 2-component, ambient-cure gelcoat also has temperature application range that extends season for restoring outdoor slides.

Creative Materials Inc.    Ayer, MA 01432
Oct 11, 2011 Available as paste, film, or pressure-sensitive tape, Anisotropic Conductive Adhesives are conductive in Z-axis and non-conductive in X- and Y-axis. During curing process, particles in adhesive become stacked in vertical configuration, providing conductivity for component that is mounted to surface, while remaining electrically insulating on X and Y axes. Applications include RFID manufacture, flat panel displays, and assembly of semiconductor modules.

Color Wheel Paints & Coatings    Orlando, FL 32808
Oct 04, 2011 To create base coat that promotes efficient use of finish coat, 1260 Flex Lox Surface Sealer is formulated for optimal adhesion, chalk-binding, and sealing as well as hiding capability. Primer is designed for previously painted surfaces and uses acrylic resins to penetrate and seal substrate. With properties that promote topcoat adhesion, low-odor solution meets LEED standard for low VOC (less than 50 g/L) and is designed as companion primer for use with Flex Lox Flat and Satin.

H.B. Fuller Co., North America    St. Paul, MN 55110
Sep 28, 2011 Suitable for processes ranging from snack pouches to difficult boil-in-bag applications, Flextra Fast(TM) SFA 8600/XR 1500 adheres to many substrates, including foil, nylon, and high slip sealants. Solvent-free product enables converters to laminate as fast at 1,700 fpm, slit in as few as 3 hours, and provide PAA decay in as little as 1 day.

Franklin Adhesives & Polymers    Columbus, OH 43207
Sep 26, 2011 Featuring 1-part formulation, water-based FilterFAB 200 PVA Adhesive offers set time of less than 30 sec and can be applied in temperatures as low as 35°F. FilterFAB 300, consisting of PVA ethylene copolymer emulsion, sets almost immediately with some repositionability and is formaldehyde-free. Suited for potting filter end caps, FilterFAB 2000 2-component, solvent-free polyurethane adhesive offers Shore D Hardness of 80-82 when cured and meets FDA regulations for indirect food contact.

Epoxy Technology, Inc.    Billerica, MA 01821
Sep 16, 2011 Designed to meet extensive certification requirements of Test Method 5011 in MIL-STD 883, EPO-TEK®H20E- MP and EPO-TEK® EK1000-MP deliver optimal thermal management and electrical conductivity. Single component, silver-filled EPO-TEK EK1000-MP is formulated with shiny finish to maximize device reflectivity. Both products are suited for solar modules and concentrators, LEDs, and high reliability military devices.

ITW Devcon    Danvers, MA 01923
Sep 12, 2011 With 4 min working time and ability to achieve functional cure in 30 min, DFense Blok(TM) Quick Patch is formulated for emergency repairs to processing equipment, even in severe conditions, and suited for patching of holes, leaks, and cracks. Alumina ceramic bead-filled epoxy compound protects against wear, abrasion, and corrosion and helps extend equipment service life. Non-sagging product can be used at thicknesses up to 1 in. on vertical surfaces and ¾ in. on overhead surfaces.

Henkel Corporation    Rocky Hill, CT 06067
Aug 19, 2011 Providing optimal bond strength to both silicon and glass and metal mounting substrates used during ingot sawing process, Loctite® 3382(TM) protects against wafer breakage. Two-part epoxy adhesive breaks down on exposure to hot water, eliminating corrosive debonding solutions and minimizing silicon waste that occurs during wafer cleaning process. Homogenous and stable, Loctite® 3382(TM) sets up in 5-7 hours, emits no caustic odor, and will not corrode equipment.

Surface Guard, Inc.    Aurora, IL 60504
Aug 05, 2011 Featuring slight difference in adhesion strength, Surface Guard® 132 and 133 provide temporary protection of painted metals and plastics. Both feature polyolefin film coated with water-based acrylic adhesive system, and exhibit low adhesion build over time when used with stainless steel, polycarbonate, acrylic, painted metal, and bright aluminum surfaces. When protection is no longer needed, products are removed with quick release. Sizes range from 1-80 in. W in roll lengths up to 15,000 ft.

Pres-On Products, Inc.    Addison, IL 60101
Aug 02, 2011 Suited for automotive, appliance, construction, HVAC, and general assembly industries, Pres-On VF tapes seal out light, air, dust, and moisture while also providing cushion against vibrations and noise. Closed-cell polyvinyl foam design is offered in several densities, including Sof-Seal, low, medium, and high. Resistant to industrial solvents and chemicals, tapes can be ordered on 52 in. wide rolls in thicknesses from 1/16-¾ in. Custom sizes are also available.

Saint-Gobain ADFORS    Albion, NY 14411
Aug 01, 2011 Designed to reinforce joints for seamless drywall finishing, FibaTape® Extra Strength Tape has fiberglass open mesh design, which provides protection against mold and eliminates blisters and bubbles. Self-adhesive product, available in 2 3/8 in. x 250 ft rolls, requires no pre-bedding coat. It is suited for applications that require additional strength, including vaulted ceilings, arches, halls, and veneer plaster jobs.